Other

When adding passengers/cargo/fuel in the EFB, the calculated zero fuel weight and takeoff weight behave erratic and show wrong values.

Hey, as already mentioned in the title, i just have a question. Does the wear and tear on the A300-600RF transfer over flights or does it get reset everytime you load a new one?

I have a lot of model matching issues with the A300. As long as I have the livery everything is ok, but when not I see Generic Bonanzas. Same with all streamers i have watched. Maybe that it is caused by the wrong ICAO codes in the aircraft.cfg for both the icao_type_designator (its "A306", not "A300") and icao_manufacturer (Its "airbus", not "aibus")? Or is there something else wrong with the aircraft.cfg of the plane or the liveries causing it?

Just updated the liveries through the inimanager and now i get a CTD every single time I try to load into the airport.

Everytime I open the bulk cargo door causes an aircraft overstress crash. Have tried on many different cargo liveries with the same result.

I'm encountering a CTD in the following situation: Livery - DHL D-AEAF Airport - Aerosoft EBBR/Brussels Optimized texture option I've done three load-ins in this scenario and it has crashed 2 out of 3 attempts. Error in event viewer: Faulting application name: FlightSimulator.exe, version: 1.35.21.0, time stamp: 0x656896c5 Faulting module name: mf3055c24e74fe5af_0.dll, version: 0.0.0.0, time stamp: 0x658dee81 Exception code: 0xc0000005 Fault offset: 0x0000000000dd7094 Faulting process id: 0x2c08 Faulting application start time: 0x01da3a50b40d566b Faulting application path: D:\SteamLibrary\steamapps\common\MicrosoftFlightSimulator…

Hi All As the title suggests - Normally, when I start a first flight i just start with the aircraft on the runway and do a few touch and go(s). However, when the aircraft is on the runway the engines are either at 100% and then when it hits around IAS 120-140 kts it will throttle back. So, i thought it was a config issue. So i started from Cold and dark and when i get to the engine start buttons, it just says arm and nothing happens. I did this again following the checklist, same thing. The engines use wont start the initial spool. Things I have tried/checked: - Throttles are calibrated - I have checked the Autopilot is off numerous times and played w…

Hello! Where can you find the folder to save flight plans created with Navigraph or Pro/Atc? Greetings

Hey folks, I've been banging my head against the wall trying to figure out this bug that's turning taxiing into a real headache for me. I'm using both a tiller/NWS axis and a rudder axis, but the problem is, even the tiniest rudder input cancels out all my NWS inputs. It's especially annoying when I'm using the brakes before a turn. I checked out some of A310 forums, and checked the EFB settings, but i found no in luck fixing this issue. Anyone else dealing with this? Thanks a bunch! Rasmus

Hi Inibuilds, Before the patch I was able to do a very long flight (7h+). After the patch, today, I tried a round trip between LFPO and EFRO. Sim got frozen 2 times (had to kill MSFS totally). First one was 15min after reaching the gate at EFRO and the second one was on the way back at FL360 15-20 min before the descent. Both after 3.5h+ flight time.

First, I want to congratulate you on the release of this aircraft. It is just great and once all the issues are ironed out, it set to be up there with the best. I love it. Please note that the beacon lights are still not properly aligned with the actual placement of the lights themselves (I hope it makes sense). They are somewhat sunk in the fuselage and even though the light reflections are correct, the light itself is not showing properly (both top and bottom of the fuselage). Could you check it, please? Regards, Christian C./

As the tittle suggests I am getting a constant CTD when i click load flight but only with the passenger variant. Is the virtual cabin to much and causing it? Anyone else experiencing this or any CTD

When taking off, it occured to me that the aircraft is already producing substantial amounts of lift before reaching the EFB-calculated VR-speed, regardless of aircraft load level. Is this to be expected?

I have a relatively good computer. Any aircraft, be it Fênix, PMDG, A2A or Just Flight, I can land and take off without any problems at any airport, whether default or third-party. Now on the A300-600 it is impractical. Using headtrack, the drop in frames is huge. Taking off or landing is impossible, as it freezes the image so much that often any action I take on the aircraft is too late. Despite being a great, well-modeled aircraft, I am quite disappointed with this point. I hope they review this and bring some improvement, I bought it and honestly I can't use the product. I formatted my computer, thinking it could improve and nothing. I have an i7 12900k, 32…

With a relatively light takeoff gross weight of 284,000 lbs, I'm seeing a super-anemic climb rate of ~700-800 fpm climbing through the high 20s. Climb performance is largely a function of thrust-to-weight ratio. A full-loaded 747-400 at 875,000 lbs with four of the same CF6 engines has a thrust-to-weight ratio of 0.26, and can climb at 2000-3000 fpm in the 20s. Compare that to a 280,000 lb A300-600F with a whopping thrust to weight ratio of 0.43--the A300 should be able to hold well over 3000 fpm in this altitude range. Something is way off in the FD thrust curves. Also, the A/T stayed stuck in TOGA power no matter what was set in the TRP--it showed climb mod…

Hi there, I request your asssistance for issue i experimented once A300-600 installed. It is impossible to make a u-turn on the runway because the nose wheel of the landing gear does not rotate as it should, remaining parallel to the fuselage of the aircraft and so for any attempt to turn. Regards Mac Joe

As the title says my avionics and lights (so pretty much everything) only works when holding right click on the mouse. It does not matter what panel state I start in either. I've tried cold and dark, APU running, and even T/O config but no luck. Any Ideas? Thank you!

Hi. First of all Great work!! Thx! I seems to have an issue with GSX. It tell's me that I am not using the same aircraft in Simbrief and in the SIM and does not load any data. This only happens with the Pax Version. I am using PAX profile you have shared days ago. KR Jonathan

I opened Navigraph Hub to update data but the A300 isn't showing up there. All of my other aircraft are there.

Hi, In LEVC the plane shows wrongly them runways, then, all SIDs in my case are badly represented.

Hello, Can we get a list of the LVARS for the A300-600? Pretty useful for ACARS programs. Thank you!

While hitting pause.. Engine 1 shuts down.. Please check for next update 🙂

Hi I can not use the Radios with PRO ATCX...any solution? Best Maik

When changing the settings in the EFB to LBS, this change is not reflected in the payload selection screen or performance calculator. Also the settings don't seem to save between flights. Regards

When I open the front left pass door, once it reaches fully open, it crashes the plane (not the game) due to overstress.