Other

Hello Inibuilds. I have requested this modification for quite some time, and it has not been corrected thus far. Can you be so kind to modify the Left and Right views (POV L & POV R in the joystick) to actual LEFT and RIGHT views as at present using those commands in the freighter version will get you Rear Left and Rear Right (over the shoulder views). This is a small fix that has already been corrected in the pax version but remains unfixed the freighter version since v1.03. These viewpoints are necessary when flying online and entering the runway to make sure there's no other traffic on final or on the runway. Thank you. Christian C./

Does anyone know if there's a LVAR for the AP disconnect red yoke button. I have my yoke setup for the toggle autopilot on/off (Spad.next) and always have to click the red button with the mouse in order to stop the warning sound. I'd like to set it up properly if there's a LVAR but I couldn't find one. Thanks

I have the latest A300 build, using an HP Reverb G2 VR headset. I notice that I can manipulate all controls in VR using the standard mouse input but when I try to manipulate an FCU knob - altitude for example, I can see the knob spinning but the altitude display digits do not change. It's as if the input is being ignored. Has anyone experienced this or is this some setup issue on my end?

As of the latest update, this is still an issue, as reported here - it skips over the part where it should say "Airbus":

I have installed the A300 600 nd have been flying the PW version. I have no tcas switch anywhere? WHY? See screenshot

Hi, Since updating to v1.1.0 my GPU utilization has decreased significantly. I now cannot attain >5% utilization on my GPU. On all other standard and 3rd party aircraft (and previously ini A306) I still achieve >85% utilization of my GPU. This has resulted in a significant drop in frame rate performance also. I have uninstalled and reinstalled the add-on I have flown from different airports, either with or without 3rd party add-ons I have reinstalled vga drivers and cleared caches I have removed all other add-ons except the A306 and the issue still persists I understand the combinations of hardware are all but impossible to cater to exa…

Hello, I performed the update for the a300 in msfs and the PW variants do not show up in the sim. I have uninstalled and reinstalled and the issue persists. I purchased from inibuilds manager. Please provide suggestions of how to fix. Thank you.

As the title says - whenever you navigate away from the en route map and then go back to it, it's fully zoomed in as far as it can go.

Will the 1.1.0 update also be available for the Xbox version?

Hi team, When is the update coming to the marketplace? Cheers.

these are all for GE https://forum.inibuilds.com/files/category/349-a300-600r-for-microsoft-flight-simulator/

Still missing the EP-FQN Qeshm Airlines https://www.planespotters.net/photo/1141203/ep-fqn-qeshm-airlines-airbus-a300b4-605r can someone paint it please Thanks best regards

Hello! I was wondering if anyone has found some good esensitivity settings for the TCA Sidestick?

This bug was reported as fixed in the latest update, but I still cannot change the altimeter setting in the EFB from hPa to inHg:

When using GSX, I have both the GPU as provided by GSX and the one that comes with the A300, at the parking stand. Is there a way to remove the GSX one so only the A300 one is rendered?

Despite using a variety of simbrief profiles, I am unable to create a feasible cargo flight from PANC-RJAA (~ 3500 mi). The EFB cannot compute the V speeds! I’d appreciate any suggestions-thanks

I just noticed the A310 manual is twice as long as the A300 manual because the former has the (very helpful) expanded procedures checklist but the latter does not. Whenever a manual revision is done, could this please be added?

I've checked all the sources for controlling cockpit lighting, but the primary flight instruments are quite dark. I would appreciate any suggestions for increasing the brightness of these instruments. Thanks-- Robert

Trying to do a clean install of the A300 (the lastest version) i keep getting a ENOENT error not got a clue what this means any help would be appreciated have attached a pic of full message Regards Tim

Hi, a few days ago I've been flown the A300 with the Honeycomb Alpha and Bravo perfectly using SpadNext. I configured all functions I need using B-Events. After the Update the B-Events are no longer working correctly. The buttons seem to be pressed in the cockpit, but no function follows. So the "hdg sel" button is pressed (also animated), but nothing happens. It stays in nav-mode?! Can anyone help?

As noted here, there is still a typo on the plane's name for both models: https://forum.inibuilds.com/topic/21975-typo-in-aircraftcfg-files/

depite no chocks, aircraft won't budge. Engines are turning and reacting to throttle input, but no movement. Handbrake off, of course. Dirk

Hello! It wasn't a problem before but after the update to v.1.0.8 it no longer works! Can you make a update!?

What are they supposed to do? I changed them on the EFB with the plain white livery but didn't notice any difference in game even after restarting the flight. The AI ATC also didn't pick them up.

Hi, the camera positions for the joystick hat switches were fixed in the 1.0.3 but I've just noticed it was fixed only for the passenger version and the freighter version still has the views set too much to the rear, like trying to look at the wings. Can it be set left/right for the A300-600RF too? Thanks!