Systems

Hello i ahve selected marker option but no sound coming out Thanks

Hello, I am having trouble with the calibration. The throttles don’t go into idle, they get stuck at the CLB detent. Even if I push the throttle down to idle with my mouse, the EFB shows them very high. I am using Beta SU1, is this a bug? I tried deleting the INI file in the WASM folder, but that didn’t work. Deleted the aircraft folder so it can stream again, and that didn’t work. Ay suggestions are highly appreciated. Thanks.

After the latest small update from Asobo, the A330 does not have clb thrust available anymore. I start with flex and after a while the plane is asking for "clb thrust". Normally you take back a bit on the throttle and it goes to clb thrust. And while reaching the right hight it switches to speed. Now that does not work anymore. It goes from flex to "man thrust" and then to "speed". Anyone know how to repair this. I already recalibrated the throttle a lot of time, but it does not matter. I use a Honeycomb throttle and the MSFS 2024 from the Microsoft store

I loaded the plane up from cold and dark and started it up and the throttle levers move using the controller but the plane doesn’t respond to any throttle movement and I’ve reset the throttle on the efb but it doesn’t do anything to solve the issue.

Dear Ini Team, On the 330 (200 and 300) when doing long haul flights, the FD are switching off automatically for no reason. I have checked every binding linked to the FD and removed them all but the issue persist. This has for effect to disconnect the AP and the plane starts doing crazy things. PS : all my assistance boxes are unticked.

Hi there, I’m writing to enquire about an issue I am facing. It is probably not an issue and is an error on my part but every time I disconnect autopilot on approach and after landing, the alarm continues to beep over and over and I can’t silence it. I tried turning FD off and on, clicked the warning button, cleared the warning on the middle display, clicked the red button on thrust levers. Nothing seems to get it be quiet. I’m not the most knowledgeable, in fact I’m quite new to it all so I’d love some tips 🙂 I have autopilot master binded on my airbus side stick but have noticed with it that it only turns autopilot on and not off. Maybe that could be the reason?

Hello, the brake pressure indicator only works with parking brakes on, it does not show any pressure when applaying the brakes on taxi or any other situation other than parking brakes on

Hello, same as in the a310, the a330 will start up and its engine run while the fuel pumps are all off. Is this realistic?

Hello. I had bit of an issue with the perfomance calculator not being able to give me perf data. It comes up with a message saying "Please complete fueling and loading before calculating take off perfomance" , As the message is very clear, I double check that my refueling, and boarding indeed IS completed... I gave it additional 15 minutes and it was still giving me this same message. This was the first time I used "realistic" boarding time option, and it took me about 23 minutes to board and 7 minutes refuel. I have made few flights with this beautiful aircraft and this is first time I encountered this. Also this was my first time using realistic loading time, instead o…

After using the "P" or "pause"-button my left engine spools down during flight and can't be fired up again. The key is selected for "toggle active pause" only, other bindings aren't existing? Is this known already and is there a solution for this problem?

Hi! Is it planned to integrate the TCAS funcionality in the near future? Makes it a little bit difficult to fly without on VATSIM. Thanks in advance! Kind regards Martin

So I’ve put this in the A330 section as it’s where I noticed it but it applies to all as listed in the title Normally I would just use INIT REQUEST to do the flight plan for me from Simbrief but I recently found this to be the reason for the sim freezing when ending a flight so started doing it manually But manual entry felt really cumbersome. Airways are slick and easy to enter - it is happy for you to simply enter the airway numbers and it figures out where they join However when you have direct waypoints, it only lets you enter one at a time. You should be able to keep adding them but it insists on pressing INSERT after each one and gives you the error “…

Hello, Can someone enter valide sensitivity values for the thrustmaster(airbus) sidestick?thanks It's not inherent to this, but every end flight(only with inibulds plane) sim crush and remain stuck it, sometimes crashes in plane selection. This is really frustrating!

I recently tried a flight from VHHH to ZBAA, and I found that the SID & STAR waypoints aren't correct, after selecting any procedure in those two airports (and I assume there should be many more), I observed many long legs on ND, and I can check from MCDU that some waypoints are 6000+nm from the route. I also tried to manually build the procedures, and some waypoints can't be found. I normally use Navigraph navdata, but I've checked that the same problem exists with Navigraph navdata removed.

Gear indication not synchronized, on the A330-300RR (not tested on other A330s) Main left and nose gear are switched around on the gear indicators, one show nose gear green the other red. (Wheel screen is correct)

First time I've flown this plane. I'm using the RR passenger variant and when I got close to CL400, it dropped down to under FL390, and then went back up and then down to FL374 and has been holding there for some time. The MCP is set to FL400. Anyone else seeing this?

Good evening, Today Navigraph released their AIRAC cycle for MSFS2024, I loaded in the A330 but I can see that the airac is not loaded and the aircraft sticks with the default MSFS24 database. Is there a workaround for this? Matteo

Is there a recommended throttle sensitivity? I have the TCA Airbus Throttle and calibrated my throttle through the EFB. However, the sensitivity between Idle to around 70% N1 is very sensitive and a little push on the my TCA would bring the thrust to 70% N1

The last two days the AP is not following my MCDU directions ,it does not descent,it is not obey speed so the plane is not flyable. I have restreamed 3 times the plane and the WASM folder without any change.

Hello, I have a issue with the tail tank. The fuel contained in this tank is never transferred into the main tank. I tried the transfer valve but it doesn't work, so I still have 2400kg left in it. Thanks

Hello, tried a flight the second time with the A330-200. The speedtape in the PFD doesn't move, it remains at its bottom. I can see the speed only in the ND in the upper left corner. Furthermore the aircraft is oscillating left and right after connecting the AP and it doesn't climb. I had to interrupt the flight. I'm sure, something is missed at my side, but I don't know what😯. The A320 works superb, without any of these problems. Thanks, Kai

Hi there, three issues Fuel: Flew from Lima, Peru to Quito, Ecuador. Had 7 tons of fuel on departure, and 7 on arrival. Yes, I have unlimited fuel turned off in MSFS settings, and default aircraft do consume fuel, at least in career. Autothrottle: Once I disconnected the AT, I wasnt able to turn it back on - i mean the light illuminated, AT mode was correct in PFD but it didnt do zip. ILS: Also, on approach to Quito I wasnt able to put the ILS freq in the FMS, neither by code or frequency. This, i'm afraid, might be a bigger problem, bc I was unable to tune ANY ILS/VOR also in Garmin equipped planes, like the VOR was never recognized in IFR training episo…

Hello, when I enter the star in the mcdu, the msfs 2024 crashes and I have to close it at the end of the task, if you want to reproduce, A330-300RR at LFPO bound for LFRS. I select the departure runway, 06 today, LGL2H. I click on LFRS for arrival, ILS Y runway 03 VALAC1C and it blocks Regards, kevin,

My a330 always ctd.Any help??

I have a situation that does not happen on all Inibuilds aircraft. In some, I can enter the Simbrief ID normally, but in others, I cannot. When I try to enter the Simbrief ID, the Xbox virtual keyboard window appears, but even when trying to enter the Simbrief ID, the screen disappears without entering anything. The problem is that it seems to enter input mode and does not exit this situation, leaving you stuck. The simulator continues to work, you can enter the menu, but the controls no longer operate the surfaces, and the simulator seems to be stuck trying to enter some information. This does not happen on the A330-200 and 300. If you try to enter the Simbrief ID o…