berkkp

Are you on FS2020 or 24? My screenshot is from '20. Also it's the Air France livery from the inimanager.

The outer gear doors seem to stay open, even when gear is retracted.

when popping out displays, it will be just a big screen with all of the DU's at once. Can we get the possibility to just pop out one DU at a time?

When displaying the route page on the FMS on any DU, the FPS drops below 20.

Hello, I am not talking about heat blur, but rather the fan blades not being blurry while spinning.

In version 1.1.2, in MSFS2020, running engines do not have any blur to them. See picture.

Ever since the latest update (V1.1.1) i am unable to hear ATC replies. I can hear the pilot's transmissions, but the ATC replies are not audible.

Anytime I edit the VHF3 frequency, at the very beginning of the flight, a wasm crash occurs.

Hello, I've encountered the same problem, and toggling the cabin light keybind fixed it, except the sliding table light, that one still does not work.

When using sim default navdata, in most STARs the waypoints generate 6 000+ miles away, dropping my FPS to about 10.

Update: Seems like there was a navdata error which added a ridiculously long leg to my arrival, resulting in a lag spike.

I just wanted to do a flight from RCTP to VHHH in the A350-900, and after entering the flight plan my FPS drop from 40 to 10.

When setting the ILS-frequency, the decimal/kHz dial jumps from XXX.95 to XXX.10, with XXX.00 not being possible. I.e. I can either set 109.95 mHz or 110.10 mHz, but not 110.00 mHz.

So the steps to multiply are: Enter flightplan in INIT page (XXXX/YYYY) Add alternate in INIT page (ZZZZ) On F-PLN page, select the alternate (ZZZZ) Select any STAR/runway, and select *insert FMC screen turns blank and whole aircraft is frozen.

As of version 1.1.2, I am experiencing a total system freeze. This happened while setting a flight from KSDF to KMEM with KLIT as alternate. When trying to insert the STAR for the alternate (KLIT), the aircraft systems freeze and are unrecoverable. I tried multiple combinations - apparently the crash happens everytime I try to insert a STAR of an alternate.

When in the A300, in v1.1.2, regardless of variant, ATC voices, except the own Pilot's voice are not audible, regardless of how the volume knobs are set.

The trimmable horizontal stabilizer seems to move into the wrong direction, trimming nose up sets it nose down vice versa. Issue is only cosmetical, the flight model/system is still correct.

Since the PW variant is out now, I would like to request a China Southern livery for the PW and a China Eastern livery for the GE variant. Just a mere suggestion/request. Kind Regards

Basically unless I increase thrust with keyboard commands, I am unable to exit the reverse thrust regime by increasing the throttle on my HOTAS throttle.

When reverse thrust is engaged, increasing the throttle with my hardware (Thrustmaster TWCS throttle), the engines will spool up but in reverse thrust rather than exiting reverse thrust. Is there any setting to stop this behavior? Usually as soon as the throttle gets moved above 0% the reversers should disengage, as in any other aircraft.

Same problem as mentioned in linked post, but freighter model only.

This was reported a couple of updates ago, was just wondering if this is getting looked after soon.

After further investigation, it seems that the values in the "PAX" and "LOAD" fields are always zero no matter the setting, which leads to a wrong ZFW value.

When adding passengers/cargo/fuel in the EFB, the calculated zero fuel weight and takeoff weight behave erratic and show wrong values.

When shutting down the first Engine (Nr.2) while Nr.1 is running, the sound of an engine spinning up can be heard. Also after shutdown of both engines, exterior sounds increase.