Modelling & Texturing

Hello, I downloaded the iniBuilds A300 MSFS Community Paintkit, and I painted the end of the flap fairings in red. However, after finishing it, I noticed that there is a blank space at the end of the flap fairings flat surface (including the antenna). Could you please help me identify the location of this area in the Wing Master file? Thank you.

Hello ini-Team, it is not possible to setup the viewpoint that it matches the official documents. Therefore i think there is something wrong with the model of the glareshield. This is especially noticeable in VR. How it should be What i observe EDDF runway width of 07R is 45m, which corresponds to the wingspan of the A300: Default view: If the viewpoint is set to see just in front of the center line, the flight mode annunciator on the PFD is not visible: Is there any chance to get this fixed, as this is an immersion killer and the A300 will stay in the hangar. There is a nice article…

Hello Team, from what I recall from my uncounted Flights on the A300/A310 cockpit, the real world pushbutton lights are much brighter than on the INI A300. Even if I set the lights to BRT, they look still far to dim for me. Best regards, Toto

This is a 2-part question really. 1- I hear there's a lower texture version available for the A300. How can Marketplace buyers access it? 2- Can Marketplace customers also use the iniManager?

Hi All, I was wondering if anybody knows where to download the A300-600R paintkit now as it no longer will download instead saying "this file has been deleted or you do not have permission contact the owner" Any help on this would be really appreciated!

Hello, I have downloaded the current Paintkit for the A300. Unfortunately any attempts unzipping the PSD files have failed so far. I tried with multiple software and computers, however the result remains the same. Can you check if there are any issues or would you have any tips if some special action is needed? Thanks, Reto

I'm doing a livery for A300-600R PAX GE engine, i have downloaded the paintkit and after painting and setting the files, when i load the aircraft in simulator the Radome on airplane noose is with a pink texture, like is missing something, but when i see other paintings of A300 PAX, all the files are in the folder, same names and same amout of files, i don't know what it can be, if someone could help i appreciate it!

The beacon light bleeds through on the GE PAX version in the cabin. IMG_5508.mp4

Does anyone notice the odd shape of the plane's head? it feels like the size of the body and head is incorrect. It looks like an indentation between the connection of the plane's body and head is this how the plane looks in real life(really doubt it) or is it a modeling error? I have some in-game screenshots VS real life, if it is an error will the inbuilds team fix it??

I've been working on some DHL EAT Leipzig liveries and really would like to change some detail in the cockpit. For EAT, the standard registration placard is a blank, isntead of it, they use a placard at the lower part of the main panel. On what texture sheet can I find the placard marked in red? I'd really like to add the registration down there, like EAT has it with their A300s. I've searched, but it's pretty hard to find it. Help really appreciated!

I wonder if there will be one if there will be an Airbus A300 600R out over the freight model and also the ST model BelugaST which is in the X plane if an MSFS2020/MSFS 2024 would come

Hi everyone! I have a weird bug in which the external lights are not reflecting on the ground. I think this happened after the SU15 but I'm not 100% sure. I asked on the MSFS Discord and someone pointed that "[the lights] are not bright enough for the light to reach", don't know if MS updated something related to that. Because I wasn't sure this bug was only happening on the A300, I made 2 videos with the exact same graphic settings, scenery, weather and time, comparing the A300 and the Fenix A320. I tried to change my graphic settings but nothing changed. I also searched on some forums but almost all issues are outdated or talking abo…

Hello all, I try to create a texture for the A300-600 with PW engines. But I noticed on the right engine, there is a security seal decal on it for no purpose. I think that sticker is for the GE engines. Does anyone know how to fix this issue? Here is my textures profile.

The texture for the RAT turbine lever is quite low-res:

I noticed the landing gear angles are fixed. It must be able to tilt on ground during takeoff rotation and landing. Expected behaviour Gear level with aircraft when airborne. Gear level with the runway when in contact with the runway. Transitions between the two mentioned above. The gear will be able to tilt so its aligned with the ground

When panning around with the camera, these two circled areas exhibit heavy texture flickering.

That means you are not going to update the nose down look? You develop new airplanes and you con not correct this............ This is ridiculous.

I know this problem has been reported in a few closed threads before Nose up to high and on discord. But the A300 currently has this issue where it does not have the iconic nose down compression look like the A330 has. Currently i have tried moving the weights to the nose which causes bad CG but has resulted in not much compresson to the nose gear itself. So i guess this is much tied to a modelling. issue. Also this bug is not present on the xplane release of this product. Is there any timeline or promise or a small hint that this will be addressed in the future? This is probably the only remaining visual gripe left with this aircraft at the moment.

Hello Inibuilds. I have a strange issue with the cabin lights on the exterior view. When i switch from the cockpit camera to the exterior camera the cabin lights are one for 1 seconds and then they go out. I am on XBOX i dont know if pc players also have this issue?.

I have just fresh installed the A300 for MSFS and 2 Onur Air Liveries all through the iniManager and directly into MSFS Community Folder. But on both liveries I keep getting weird black textures on the doors on the Left Side of the Fuse. Can anyone help me if you have seen this before? Thanks, Alex Chard

Hello everyone! Since the A300-600 is already of very high quality, I don't want to mess anything up with mods. There is an "External Lights Fix" on the well-known add-on website and my question is whether it is really "necessary" to download. I assume the lights adjusted by the mod are also fixed in the original version? Or will be?

Hello, the DHL livery on xbox the nose is like gone and the textures are very weird

With the latest build, there is missing text on the panels aft of the throttle quadrant when the IDC is enabled. When the IDC is disabled, the text returns. Attached pictures are from the freighter, haven't checked the passenger variant.

Hello, I am in the process of making a livery, and while doing so I noticed that in the Ext Placard PSD there are hazard area decals in the engine layer group, however I could never get them to appear, I did some looking in other liveries on this website's downloads section, the only livery I could find that these engine decals would appear in, was the Iran Air EP-IBC. Can you give me any guidance as to what I am doing wrong? Many thanks in advance and happy May Day.

Hi Team, I´ve noticed that the geometry of the VC seems to be off in someway ( in VR ). When I align my seat with the red and white balls on the center window column, I´m unable to see the FMA. In order to make the FMA visible, I have to set my position unrealistally far back or unrealistically low ( when setting the seat so low that I´m able to see the FMA, I wouldn´t be able to reach some parts on the Overhead like Fuel Pumps, Packs, etc. ). I think the easiest way to fix this is to lower the position of the PFD. Thank´s for looking into it ( please try in VR ). Best regards, Toto