Other

I have a weird issue where the -900 works fine in regards of the ANF but for some reason the -1000 doesn't. When I attempt to connect with Navigraph the ND shows the message "ARPT NAV NOT AVAIL". Also I tried using the ATC COMM page to request weather but I never get a response just "Pending Request".

Hi there, Is there anyway to editing default view point for A350? Because it doesn't change anything while loaded the plane after editing camera.cfg, thanks!

1) The Documentation button is missing 2) brightness buttons not working ... display very dark 3) Ground : stairs button missing 4) Terminal charts not indicating ( I have a valid Navigraph subscribtion ) 5) Failure simulation missing pls update the 2020 version

Profile for Inibuilds A350 using Logitech panels and TCA Airbus Edition for additional buttons. It does work with some limitations,so you can amend if you wish. Autobrake BTV works really well so long as you meet the criteria within the A350. This is available from Flightsim.to Regards Dave

Hi folks! I would like to ask if you can see your chocks when they are on! Since last update, I can´t see them!

Hi. I have a modified TCA with a lifting spoiler arm lever. However if I move the spoiler arm along the axis it no longer works, and it appears the spoiler axis doesn't return to 0 in the aircraft (visually and within spad.nxt it does). The ECAM message still says the speedbrake is deployed. Is there any way of calibrating the spoiler axis? As I use spad.nxt the Microsoft controller profile is completely blank and everything is handled by spad.nxt The spoiler arm button is wired to the eng fire button but for it to be recognised by the sim the axis needs to be in the speedbrake off position

I've suffered a CTD on two flights in a row, where the pause at TOD feature was active and the sim had to wait until I'd finished my dinner. After about 45 minutes, I get a DXGI_ERROR_INVALID_CALL (0x887a0001) FS20 crash with my 32GB of RAM almost completely used (usually around 14GB). Today I'm trying the flight for the 3rd time and I've let it stop at TOD again. I noticed that the sim isn't actually paused, the time on the SD keeps running. At the same time, the GPU shoots up at least 5% above what it was. The previous two crashes also showed that the sim time is still running, because it was night in both cases, having started the flight in the afternoon. …

Works fine in 2020 but does not appear in 2024 nor do I see any way to install it. Also, the IniManager says no products andso how can get the liveries? Thanks and regards!

Imagine this, you are on approach after a long flight with the brand new A350, when all of the sudden after disconnecting the AP1 along with A/T on final approach, you notice that the roll inputs are slow, as expected at slow speeds, but they're unusually slow. As if the plane is taking its time with moving from side to side as needed. Everything is a-okay with the pitch, yet you cannot keep yourself on the centerline because the plane keeps rocking around leading to a go-around and a later autoland procedure to get back on the ground. I am aware of atleast one post regarding this issue and I too, doubt that this is the fault of sensitivity settings. The effort …

There is a problem that MFD, ND are not clickable in pop up windows on multimonitor setup just OIS works. Is there any method or workaround available for now? or this feature planned to be implemented in future updates ? Comments appreciated

Really frustrating that the auto tune feature for Beyond ATC only works some of the time for this aircraft. No other aircarft has this problem and BATC cant fix it because they believe it is the A350. Just add this to the numerous problems with this aircraft I have for a $120 AUD purchase. Please look into and fix or at least ackowledge that someone could look into it.

Hi guys, I recently bought the a350 from inibuilds and when I started the engines I saw green flow around the engine. Can someone explain how to fix it please? Thank you very much for your help !

MSFS2020 Last update v1.0.2. all cockpit totaly unclickable since i've got it. WASM folder was cleared as instructed by iniBuilds several times. Can't perform even my first flight. Any suggetions?

Was perfect before 1.05 now very twitchy and super responsive. Also when power applied on runway it immediately stops the use of nose wheel steering and goes to rudder steering. anyone else have this issue ?

- Overall FPS A LOT BETTER than previous versions especially from extiror view. But small stutters and FPS drop still present during taxi and after landing. - Managed Cruise Speed Managed Cruise Speed still wrong in lower levels. Did a flight today curising level FL310, managed climb speed 300 KIAS/M0.85, managed cruise 264 KIAS/M0.80, managed descent speed 310 KIAS. - Pulling out VS knob will cause a nose pitch down Pulling out VS knob any time will cause a abrupt nose down movment with a vertical speed of -100 to -200 fpm then gradually return to where it was or to selected VS. AP disconnect - I bind AP OFF to my stick and when I use …

(MSFS 2020) Update suggested that this was fixed, but swapping active and SEC1 then swapping back led to original full flight plan being lost ... start again!

2025-03-22_01h11_39.mp4 1.0.5

Programming the end waypoint for an offset segment of a flight is usually "interesting" in the FMS, with different waypoint then displayed in the box to the one either selected or "typed" in. At the end of an offset to the right (by 2 miles for example), the plane turns left to get back on track but then continues left in a full circle! Has happened multiple times!

... has usually been fine but the attached screenshot shows nonsensical time for T/D on today's flight with T/D at 20:54, long after expected landing at 20:36 !

Trying to figure out if im doing something wrong,everytime i go to do a flight with he same plane (tail)my oil,batteries everything is topped of and full and not where it was when i landed, am i doing something wrong here or is it going to start fresh all the time when you reload the sim.

after making a direct and press the videom bottom all screens freeze

In msfs2020, the flight plan in SimBrief has been imported into the OIS, but when the ‘Copy Flight Plan Request’ on the MCDU is pressed, it goes to the ‘Pending’ state and then returns to the ‘Copy Flight Plan Request’ state after a few seconds. There is no response. Even after a long wait (5-10 minutes), there is still no response. Re-entering the SimBrief ID and Navigraph does not help. I tried deleting all the living and clearing the WASM folder, but it still doesn't work. I've tried everything I can find in the community, including saving the ‘Enable Detailed Navigational Logging’ setting, but nothing works. How can I fix this issue?

Hi there, Before I prepared for descent and set the BTV, I found that the airport map was unavailable. In the settings, I discovered that the map was disconnected, and no matter what method I tried, I couldn't reconnect it. The Navigaph works fine before taking off. I have encountered this issue twice, both times after a long flight. A350 V1.0.4 FOR MSFS2020

Has anyone encounrted this issue? I have after attemptinng completing a trans atlantic. I can't really determine what the source of this issue. But can tell my plane entered A.Floor and the autopilot was disconnected. As i was AFK from PC.

I recently updated V1.04 of the A350 and for some reason it is invisble what do i do???