Modelling & Texturing

RTX 5080 64Gb ram,MSFS 2024 in VR Meta Quest 3 the panels are not displayed properly, fcu the buttons are see through and overhead panel the buttons are not displayed and see through RAI_20251025_142817.zip

The N1 animation accelerated way too quickly, there are some good references available for comparison with the in sim behavior.

MS2024 The aircraft shows up normally on my monitor textures are fine. When I switch to VR the textures are incomplete partially transparent and wholes where the buttons and nobs should be. This has never been an issue until recently. whats going on ?? All other aircraft work fine............... (Crystal Light - RTX4090 - i9 - 64G Ram )+MSFS2024 only not working MS2020 the A350 works fine

Hello, I'm trying to make a config for my Virgin Atlantic liveries. I've managed to find this: URL to MSFS 2024 Livery Config Instructions - which goes into detail on how to do the livery configs. However, it seems the instructions are wrong or something is missing. On instruction #1, it states about Package Definitions. Yet on #2 it talks about PackageSources folders. But, there's no folders with that type of information in any of the liveries? I thought I may have done something wrong, so I downloaded the paintkit from the Inibuilds website yet it displays exactly what I've done in my liveries. Can anyone help me out here because I am so confused and…

Hello, after latest update the interior cockpit is totaly blurry (anche screens are greyed out) during the night: But if I move the time slider to the daylight... everything is fine. Tried to reinstall the aircraft but nothing happens... suggestions???

Hi, so I‘ve come across the Winglet-issue. Some Liveries (Edelweiss, Emirates and prob. more) seem to load the winglets blank. Sometimes they pop up for a milisecond but disappear again. I haven‘t tried the .cfg trick yet but I just wanted to make sure that might be something to look into. Anyways, keep up the great work and thanks for everything! Best regards!

I cant open 4L at all by clicking every other door operates normal by clicking into the clickspot

I have tried uninstalled re install all liveries and aircraft. I am running 2024 with the latest beta.

Hi everyone, before getting into this one, I'd like to leave some appreciation for the ini team. The way you listen and care since release is nothing we should take for granted in the flightsim world. Thank you for this and keep up the amazing work! Now back to business: I've noticed that on v 1.0.7 the entire aft cargo door is misaligned when opened. Also on the left edge of the door, the mesh has some issues. Cheers!

In reality, the small lights on each cabin door can be turned on

I have noticed that the cabin windows of the A350 have unusual reflections. Terrain and cloud layers are reflected onto the windows through the aircraft fuselage, which greatly affects the visual experience.This issue has not yet been fixed in version 1.16

Cabin signs problem still persisting? Im using the "q suite cabin", have'nt tried the default cabin yet.

Hi. I don't know what happened, but when I use A350 now the livery is incomplete and all pink. What should I do to restore the correct configuration? Thanks for the help

SU3 LOD is not fixed, deleted the entire A350, installed latest 1.5 version totaly new reinstall and its the same Autopilot is gone, missing buttuns and just a mess

Hi everyone, I've just noticed a little inconsistency I'd like to pass on. On Flaps full, the inboard linkage on the outboard flaps is clipping through the flap actuator shaft, aswell as the wing's edge. This is especially noticeable during rollout with the spoilers fully extended. I totally understand that your art department probably has absolutely no idea or documentation about where this goddamn rod goes during retraction. 🙂 I can't tell either, however I've at least found some footage showing that it's actually mounted higher up on the wing than it currently is in sim: Adjusting this should at least eliminate the clipping. …

The rain effect on the windshield appears on the HUD glass. As shown in the image, the rain effect appears in front of the HUD glass layer.

Seems to only happen with the basic Delta liveries, or at least those are the only ones I've found with this bug. A bit hard to describe, but there's like, a ghost-door from the landing gear bay that shows only from certain angles, as if the bay doors were open, but from all angles the landing gear doors have no color to them (tried to show it as best as I could in the picture). Also the winglets have a weird white splotch through the Delta logo. I have many Delta liveries downloaded (from the inibuilds app itself) and the same bug appears on ALL of the basic Delta liveries, all the special liveries are fine.

Hi Team, It seems that the textures for the JAL winglet is not done correctly for the long winglets on the -900 variant as per attached image. The outside facing textures are fine, just the inner textures seem to be missing an area. Thanks, Wisam

Hi Inibuilds team, One thing I’ve noticed is that even at the lowest dim setting, the cabin lights are still far too bright, especially during night flights. It would be great to have the option to turn off the cabin lights completely, or at least reduce them significantly more than is currently possible. Right now, there’s still noticeable light reflecting off the window panels, which really takes away from immersion, especially when flying at night or from the passenger view. Would you consider adding a proper "lights off" option in a future update? Thanks

since the SU3, the inside the cargo hold and the lack of the passenger cabin means you can see straight through it on external view and I dont know if anyone is having this same issue