sk0941

Don't think that the missing STARs is Ini Builds fault. I just did a test, loaded the sim with the default LIMC scenery and all the arrivals are there, then I loaded the sim with the Aerosoft LIMC and all the arrivals and approaches are now gone. So for this issue I'd go and bother Aerosoft 😛

Happened to me to when over the Atlantic a couple of hours into my flight

Same issue here

Still not fixed in 1.0.9

I've noticed that in 1.0.8 I'm not able o change the STAR or the approach once I've programmed them. If get assigned a different STAR or approach midflight my flightplan will disappear and send me direct to the initial waypoint of the STAR or the approach. To fix it I've had to reload the flightplan in the MCDU, load in the new arrival and approach and then go direct to the waypoint I was going to before it all disappeared.

Same here, in 1.0.8 I no longer get the "Auto brake off"

Is it a 350 issue or some weird sim limitation? Was flying EKCH-PANC and near 86N040W the sim just freaked out. it said on the PFD that "AP INOP" plane started turning here and there and the frames were less than 1 fps

I've tried with rudder tiller both on and off but same result. In external view the wheel turns but nothing is happening...

I've had this happen multiple times in 2020 as well

Flight went nice from KLAX to PHNL until I was passing about FL220 on the descent. All the displays decided to freeze. I when it froze I went into the ATC COM page on the FO side if that's any help. Please fix this issue that seems to be happening to a lot of people

In the GE variant I have about 15% of oil in both engines, but I'm bot able to service the engines. When ever I click "service engine" I get met with a prompt that says "unable to service engine with cover in place" or something along those lines. The thing is that I don't have any engine covers in place, I don't even think there's an option to place any atm. So how would I go about restoring the amount of oil in the engines?

By default the jetway position of gate 239 is too far out. I can't follow the VDGS all the way in without hitting on of the jetways. You can also see that they aren't at their starting positions

Nevermind 🤦‍♂️ My throttle calibration had been reset somehow, the idle on my throttles were equal to 50% somehow. Recalibration did the trick.

1.0.6 for PC

I have it so that when the button is held it sets that lvar to 1 and on release it goes back to 0. that works for me at least

Did a flight now and had to ride the brakes on the ground when taxing out. Leaving the throttle in idle had me taxi at 36kts and more. I had the same issue after landing, only that after landing the brakes got hot so they stopped working after a little bit. I tried to taxi using only 1 engine and even at idle it had me going over 20kts.

Right must've been a one off? Things behaved as expected this time around.

I'll try tomorrow and see what happens

I was doing a turnaround, but when I loaded the next flight from Simbrief all fields were left blank. I loaded the new flight in the EFB, that was all fine, requested teh flight via ACARS and all the fields on the INIT page were left blank. If I put BIKF/BGSF in the top right, it'd bring up the whole route, asking if I wanted to insert it. If I pressed "insert" it'd bring me back to the INIT page with all fields left blank.

I've noticed that when the planswithces to mach numbers the LVAR for the speed dial doesn't match what's displayed in the plane anymore. In the attached picture you can see that the selected speed is Mach 0.76 and the LVAR is showing 0.7476.... which makes setting up an autopilot panel a bit tricky. Because if I just round the LVAR it'll give me the 0.75 in this case on my end and so forth. It will be accurate for some speeds but far from all. It's a quality of life thing, not the end of the world but great if someone could take a look at it. Great plane btw.