ekosif

I understand that but what is the point keeping it on the AUTO if you are not going to use it at specific condition? Just switch it to Auto when you want to use it. At the end of the day, auto selection is not there to automatically enable/disable it, it's there to adjust time compression level when it is activated.

No, I disagree with this one. Sometimes I am using it for accelerate the boarding to save some time and this is also valid for all other aircrafts like pmdg. If you don't want to use this function on the ground simply change the time compression from auto to off in the OIS.

It shows the other side OIS. Instead of toggling between the pages you can open charts on one OIS and OFP on the other one and switch easily between them with just one button for example

I am checking the OIS before starting to flight and if there is any QR code there, I am restarting the flight and check the OIS again. Works for me every time so far. PS: Normally even though there is a QR code there to sign in, I am not doing anything except restart the flights. Most of the time it is automatically logged in when I started again. If not then I am entering the code and then restart the flight.

Same here, all systems are frozen around FL174 and therefore aircraft was not following the routes etc. I was able to fly it manually but of course no guidance neither on PFD nor on ND. This is my maybe 25th flight with this aircraft, second one after latest update, there were no major issue so far except for the cabin announcements which is not deal breaker.

Will try it, thank you.

This button normally transmits your voice to the cabin, when you press and hold it you can make announcement to the cabin, it shouldn't affect the hearing under normal conditions. But I tried anyway, doesn't work again. When you press it, it disables your microphone for vhf1 as well.

I am pressing PA button as habit from fslabs back in P3D days.. Before starting APU and boarding, during setting the ground frequency, after loading the aircraft from EFB. It lights up in my PC. But I am not able to hear anything. I understand that announcement behavior is changing from person to person in this case. Therefore, not pressing the PA button is not only reason.

I am pressing PA button as habit from fslabs back in P3D days.. Before starting APU and boarding, during setting the ground frequency, after loading the aircraft from EFB. It lights up in my PC. But I am not able to hear anything. I understand that announcement behavior is changing from person to person in this case. Therefore, not pressing the PA button is not only reason.

Thanks a lot 🙂

I am using both 900 and 1000 variants. Already made more then 10 flights. By the way, I didn't use third party liveries, all of them were downloaded via inimanager.

Thanks for feedback but I can hear the announcement if I switch the cam to the cabin, but nothing when I came back to cockpit. Therefore it is not related with it for me unfortunately

Always doing it during preliminary preperations but still not hearing anything.

I solved it by zooming in a bit more to MCDU. If you try from far away, it is very hard but working very well for me if you get closer.

No, you can hear on 2020 as well if you change the camera to the cabin. I am not able to hear anything from cockpit so far.

Hello, During descend, let's assume I have 220 knot speed restriction. While I am continue my descend with 220 knots in managed descend mode, if I direct to next waypoint, it resets all the speed restriction (current speed restriction already in place) and go back to 250 knot. Therefore if ATC gives you a shortcut, I need to set the speeds manually every time until next speed restricted waypoint.

I have same issue and also already created a topic for it. For the work around, after starting the flight, directly check the OIS. If it is showing QR code to logged in then go back to main menu and start the flight again. You will see that QR code will be gone and everything will work with this way, no need to log in again.

I have same issue and also already created a topic for it. For the work around, after starting the flight, directly check the OIS. If it is showing QR code to logged in then go back to main menu and start the flight again. You will see that QR code will be gone and everything will work with this way, no need to log in again.

I always load the aircraft from tablet first and then select GSX to board. It is working with this way with correct PAX numbers

I have same issue and also already created a topic for it. For the work around, after starting the flight, directly check the OIS. If it is showing QR code to logged in then go back to main menu and start the flight again. You will see that QR code will be gone and everything will work with this way, no need to log in again.

I have same issue and also already created a topic for it. For the work around, after starting the flight, directly check the OIS. If it is showing QR code to logged in then go back to main menu and start the flight again. You will see that QR code will be gone and everything will work with this way, no need to log in again.

I found a work around for this issue.. Before explaining it, let me summarize the issue again. I have Navigraph subscription and ANF function is working before take off. There is no issue with it. BUT, after take off and climb, when I switch to PLAN mode and zoom in to set the BTV function, it was giving this error. Again, it is working before take off during taxi from gate to runway. For the work around, after get in the cockpit in the cold and dark situation, I wake the plane up and directly check the OIS settings. If it shows the current airac version then it is good to go. But sometimes, even though I logged in with Navigraph subscription, it is showing QR code to log in. If I continue like this, I am able to access the charts and ANF before take off but not not BTV or destination airport. Therefore, when I see the QR code there, I am just going back to main menu and start the flight again. With this way, it seems it is logged in again without doing anything and all the systems are working. Hope I could explain.

Got the charts on 2020, that was really quick fix, thanks inibuilds!

Hello, I am getting 'ARPT NAV NOT AVAIL (NAVIGRAPH)' error when I try to set BTV even though I have Navigraph subscription and it is not showing the airport thus unable to select BTV and see the airport map during taxi to gate. I have tried this on couple of airports, one of them is Munich (EDDM) but no luck. I can see the airport map during taxi to runway before take off, but not for landing.

If we zoom in all the way down to see the taxiways in OIS under enroute chart section, airplane location is not correct and has offset. Navigraph APP and ANF in the ND seems OK but OIS shows I am going on next taxiway on the left.