[Fuel Temperature]

2 hours ago, Philippe TORNE said:

Hello after 6h30 of flight the fuel temperature is the same as it was at departure.

Best regards

It seems hard coded and stays always 17 Celsius. Nothing modelled here. They have changed it from minus 20 to 17 celsius with the update 1.0.1

[OIS VAPP Not changing when switching CONFIGFULL or CONFIG3]

The OIS (and FMS blue value) does not show differences in VAPP Speed when switching between CONFIG3 or CONFIGFULL Landing.

The landing distance required is increasing when choosing CONFIG3, but the VAPP stays the same (in my case 144 at arriving OMAA via 31L).

I do expect a higher VAPP when selecting CONFIG3 in the landing performance calculator

[OIS VAPP Not changing when switching CONFIGFULL or CONFIG3]

The OIS (and FMS blue value) does not show differences in VAPP Speed when switching between CONFIG3 or CONFIGFULL Landing.

The landing distance required is increasing when choosing CONFIG3, but the VAPP stays the same (in my case 144 at arriving OMAA via 31L).

I do expect a higher VAPP when selecting CONFIG3 in the landing performance calculator

[RNP RF Fix Leg not drawing properly]

Also at GATLA1A into FMMI the case when suing RNP29 for landing. 

Exact the same draw pattern as the OP mentioned. 

It should have been a 15dme arc. The ND  does not draw an arc. 

[Enroute charts in OIS has offset when zoomed in for taxi - not synced with ANF in ND or Navigraph App]

On 2/27/2025 at 3:26 AM, ekosif said:

If we zoom in all the way down to see the taxiways in OIS under enroute chart section, airplane location is not correct and has offset. Navigraph APP and ANF in the ND seems OK but OIS shows I am going on next taxiway on the left.

Exactly. I see this also. Plane is offset and the chart is updating its direction with a huge leg and therefore always far behind my exact location (on top comes the sidewards offset as the OP mentioned)

[Inaccurate fuel temperature simulation.]

It seems scripped, not programmed.

Means, regardless the outside temperature it will most likely always show minus 20 at crz...

@iniBuilds

Are you able to develop a outside temp and time based cooling Process? That would be awesome. 

[Poor Exterior Performance]

14 hours ago, alxvown said:

I did do a quick test to ensure this performance issue did not have to do with the scenery/ AI traffic by removing both factors in my test.

 

Without any addon scenery or AI traffic my FPS in the cockpit holds around 30 FPS. 

 

Outside the FPS drops to 15-20 FPS. The system will lag harder whilst panning. Not sure if there may be room to improve the exterior modeling?

Exactly also noticed outside FPS is much worse compared to inside

[Incorrectly defined 1L DOOR]

same here, 2020 and 2024

[GSX integration issues]

GSX Integration is activated. When openeing GSX menu in the OIS, click on GSX next page in OIS does nothing. 

[Terminal Charts not showing up?]

7 hours ago, Quinton Law said:

Besides, I have a problem while releasing the parking brake. When I was releasing the brake and ready to push, the aircraft started to have warning appearing, sounded like beepbeepbeep. MSFS showed aircraft landing gear damaged because of me>

You could try turning off the GSX setting where the aircraft get lifted up on PushBack. I have turned this off in GSX menu (can not recall how it is called) but there must be an option. This bewares you from aicraft is "fallen down" after pushback and damaged gear probably. Maybe you can try it out. I do not have any issues so far with a broken gear and using GSX for pushback as well

[Terminal Charts not showing up?]

+1 here. MSFS2020 and just linked my account. No charts able to view. 

Seems to me the Token does not get updated/set.