alxvown

Hello team, I was a part of the WASM test build prior to 1.2.6 going live and have found that, since downloading the stable live version, I have had a ghost WASM crash on every flight I try with the A350. These flights have varied from 3-12 hours. I am not sure if this is a known issue, but when I install the 1.2.6 build on its own without the WASM test build, during flight I check the inimanager and it shows the test build also installed alongside it. I believe this is happening when I start the flight up for the first time after clearing the WASM folder. I have never installed both the test + stable build myself. When I tested the WASM test build I only had 1 ghost WASM crash. I tried to just install the test build by itself since the 1.2.6 stable release, and again, midflight noticed that the stable release downloaded itself in my manager without being prompted. I am unsure if both builds are meant to be installed at the same time or if this is an internal error causing WASM ghost crashes en route (buttons unclickable) I attached my settings too to show that the installer should not automatically be downloading or updating any of the products without being prompted.

I had this issue too 😞

I too have tried to be patient loading this product; however, I have now waited over 45 minutes for it to load. I have had many high fidelity products in the past but none of them ever took this long. Not sure if there are any tips to assist. 45+ minutes to load a new aircraft is not typical.

So far no changes in performance for me. Honestly the modeled interiors if they could be toggled off that might help.

Out of curiosity is there another planned update to help with LOD optimisation. All sceneries I have LAX, LHR, SAT have awful FPS stuffers. I have lowered my textures and graphics settings to medium which is VERY low for the type of computer I am running. Every other addon I have added (airports/ planes) have never effected the simulator to this extent 😞 I use AIG traffic but that only takes 5 FPS. Device name DESKTOP-V4C6SN7 Processor Intel(R) Core(TM) i7-9700K CPU @ 3.60GHz 3.60 GHz Installed RAM 16.0 GB (15.8 GB usable) Device ID 9CA68F0D-7A8F-4179-BAEB-562F67659B32 Product ID 00325-81693-08134-AAOEM System type 64-bit operating system, x64-based processor Pen and touch No pen or touch input is available for this display RTX 2070

What I found sometimes works is only start AIG and turn off couatl before loading the flight into the sim. This way couatl doesnt auto load any objects in. If AIG shows you can then test loading couatl into sim after startup of flight.

Hey there. I now own 3 inibuilds sceneries and noticed that all of them take a HUGE chunk out of my GPU. Any chance you could list the "ideal" settings in MSFS to help with performance. I have AIG installed and GSX which I would love to have work with these sceneries without disruption 🙂 I constantly get CTD errors when loading these sceneries.

Update: finally got a full take off roll without any error messages. Will be playing around with settings to see what works and looks best bc I miss my lovely ground world textures at 200 LOD haha 😉

Let me adjust the settings to the ones you reccomend! Thanks for being so patient 🙂

Ah shoot! I have a RTX 2070 super if that is what you were asking. And that is too bad that the scenery can't run smoothly in ultra. All of my other payware sceneries work fine. EGLL obviously has some issues but that is mainly because of the city optimisation issues.

Just played around with deleting that folder

Just played around with deleting that folder and same message again ;(

I have rolling cache off and have cleared the cache manually and still no fix 😞

Did some further research. Since SU10 update there is no way to regenerate the content.xml after delete. Not sure if this affects your advise. I tried opening the sim again after trying the steps again and same message.

After reopening MSFS only the scenery rebuilds but no content.xml