When reverse thrust is engaged, increasing the throttle with my hardware (Thrustmaster TWCS throttle), the engines will spool up but in reverse thrust rather than exiting reverse thrust. Is there any setting to stop this behavior? Usually as soon as the throttle gets moved above 0% the reversers should disengage, as in any other aircraft.

Basically unless I increase thrust with keyboard commands, I am unable to exit the reverse thrust regime by increasing the throttle on my HOTAS throttle.

I've found the same and the only answer for me is by using the keyboard F3. But, the A310 works as it should?

Del

Use reverse hold.  When this is activated, it puts the aircraft into reverse idle.  Moving the throttle forward will increase the amount of reverse thrust.  When ready to stow reversers, move the throttle back to idle and deselect reverse hold.  The throttles then go back to normal operation.  

Looks like this on the in sim bindings assuming you don't use AAO or Spadnext. There is no provision for engine 1 or 2.  It holds all reversers.  

Edited February 15, 20242 yr by Crabby

7 hours ago, Crabby said:

Looks like this on the in sim bindings assuming you don't use AAO or Spadnext. There is no provision for engine 1 or 2.  It holds all reversers.  

Speaking of which, I tried to map the "hold reverse thrust" in AAO last night but I could not get it to work - it would only work by pressing and releasing the button on my controller (I tried the two reverse thrust commands but ended up with the same result). Is there something I'm mapping incorrectly here?

1 hour ago, LukeFF said:

Speaking of which, I tried to map the "hold reverse thrust" in AAO last night but I could not get it to work - it would only work by pressing and releasing the button on my controller (I tried the two reverse thrust commands but ended up with the same result). Is there something I'm mapping incorrectly here?

Upon further review, and I had long ago forgotten about this, I actually have that mapped in the sim.  AAO has a problem with that command.  I thought it was fixed by now but apparently not.  It had been so long ago, I forgot about this.  I will get a hold of Loriby and see what the progress is on this.  In the mean time, map it as above.  

15 minutes ago, Crabby said:

Upon further review, and I had long ago forgotten about this, I actually have that mapped in the sim.  AAO has a problem with that command.  I thought it was fixed by now but apparently not.  It had been so long ago, I forgot about this.  I will get a hold of Loriby and see what the progress is on this.  In the mean time, map it as above.  

Got it, thanks. 👍 Yes, I've used it as mapped in the sim and found it to work flawlessly.

Edited February 16, 20242 yr by LukeFF

6 minutes ago, LukeFF said:

Got it, thanks. 👍 Yes, I've used it as mapped in the sim and found it to work flawlessly.

Holy Crap!  I haven't tried it in a while.  This works.  I have not tried to hold the individual engines, just both.  Sweet.  I have V4-10 b57 i think.  Give it a whirl.  Notice I added a key up with a 0 in it to make sure it comes out of reverse.  Seems to work.  I am going to go change all my aircraft now!  Sweet, God knows I love a blank in sim profile!.

Edited February 16, 20242 yr by Crabby

Ok, I can confirm that works for everything but the Fenix.  I think it has to do with their half in the sim half not in the sim/throttle config and just the Airbus throttle operation in general.  So, that one stays in the sim.  

19 hours ago, Crabby said:

Holy Crap!  I haven't tried it in a while.  This works.  I have not tried to hold the individual engines, just both.  Sweet.  I have V4-10 b57 i think.  Give it a whirl.  Notice I added a key up with a 0 in it to make sure it comes out of reverse.  Seems to work.  I am going to go change all my aircraft now!  Sweet, God knows I love a blank in sim profile!.

Thanks, will give that a try. 👍

Heya!

Sorry for the late response 😕

Is this still an issue?

Be sure to go into the EFB and set the options to say Reverse on Throttle Axis - Yes. Right under calibrate Throttle. (A310-300)

Edited August 11, 20241 yr by Poody

15 hours ago, Poody said:

Be sure to go into the EFB and set the options to say Reverse on Throttle Axis - Yes. Right under calibrate Throttle. (A310-300)

Not many controllers have an actual reverse throttle axis.  If you have one of the majority controllers without, doing this will add a fake amount of axis as a reverse and cause many to go in and out of reverse at the most inopportune moments imaginable. 

On 3/3/2024 at 5:31 PM, Deleted Account said:

Heya!

Sorry for the late response 😕

Is this still an issue?

Never was an "issue".