Systems

Even after throttle calibration in the EFB and making sure that Reverse on Axis is on, when I put my throttle into reverse, the throttle in the sim just stays on Idle. My throttle quadrant is the Thrustmaster TCA Airbus Edition Throttle Quadrant. I have tried applying deadzone, going into the game files to turn on Reverse on Axis (was already on) and tweaking and resetting the calibration an bunch of times but it doesn't work. Thanks for any help!

Hello iniBuilds Support, I’d like to report a potential issue with the A320 APU behavior in both Microsoft Flight Simulator 2020 and 2024. I’m not fully sure if it is consistently reproducible, but I’ve seen similar reports from other users experiencing the same behavior. Configuration: MSFS 2020 and MSFS 2024 All assistance options disabled No key bindings assigned to APU controls What I observed: Starting from Cold and Dark, the APU behaves normally until engine start. After engine start, the issue occurs. Steps I followed: Start Cold and Dark Follow normal startup checklist Turn ON APU Master Switch Start APU…

Hello, I am flying on Xbox Series X using MSFS 2024 and the iniBuilds Airbus family (A320neo and A321neo), and I would like to report some major issues that are consistently affecting my flights. The main problems are: Using DIR TO often breaks the flight plan completely. The route may still appear correctly on the navigation display, but the aircraft no longer follows it. LNAV/NAV mode becomes unreliable after certain inputs. Even when NAV is shown as active, the aircraft does not properly follow the programmed route. After using HDG mode, switching back to NAV often does not work correctly. The aircraft may remain in a sort of “stuck” behavior d…

Hello, I have encountered a weird navdata problem when flying A320 v2 to Cork (EICK) I was flying inibuilds/Asobo A320neo v2 and the ILS frequency in the FMS for runway 26 was 109.5, whereas it should be 109.9 I believe. In any case it did not work. As this happened immediatley after the navdata update, I first reported the issue to Navigraph, as I thought something was wrong with it. Their support investigated the issue, and came out with the following: Problem seems to be specific for A320neo v2, or at least on some other aircraft it does not occur, Problem only occurs if the handcraftdd EICK is on - if it is off, the ILS works, Problem occur…

After an update on the sim, the A320 and other Airbus default airliners would not load passengers or fuel at the instant or fast speeds through the inibuilds EFB. Is this a bug with the plane?

I followed a lot of tutorials on YouTube and they all do the same thing and I do that and everything is correct because it’s basically the same as starting up the a321lr and I can do that but with the A320neo the flight plan and everything is set and when I takeoff I put it into autopilot and I turn off my controller because I don’t need it anymore until landing and then around 10mins in the autopilot disengages and so does the flight director and when I turn it on again it just points up to around 40000ft and then dives down and does its own thing. I do the exact same thing with the a321lr and use simbrief for both and it works perfectly fine with the a321lr. Any idea of…

The issue I’m facing with all base iniBuilds aircraft is that my flight plan and other data are not being transferred from the EFB to the MCDU. I have my SimBrief ID correctly entered in the EFB. When I click Sync, everything loads properly — I can see my OFP, weights, fuel, runway, etc. However, when I go to the MCDU to perform the DIFSRIP procedure and try to load my data from SimBrief via the uplink, I simply don’t have the soft key for it (no INIT REQUEST option). My flight plan in the MCDU only shows the departure and arrival airports, which I believe come from MSFS’s preloaded route (when I set the departure and destination in the Free Flight menu). Becaus…

I’ve only been able to do a few successful flights in the new sim, my favourite planes are the airbus family, I’ve flown to a few different airports such as Melbourne Intl, Bahrain, Dubai Sydney, and all have seemed to have a similar problem, all is well during takeoff, climb, and most of the way through cruise, but the first of 2 problems is (I’m unsure if this is a simulator side bug or iniBuilds side) but the plane when following the magenta flight plan seems to start slightly waving left to right slightly and it’s also seen on the Flight Director (even in calm winds this happens), but the second and more bothersome problem is on final approach to aforementioned airpor…

I have a WASM crash in the A320neo when I choose the ILS I25-Y for SCCI. Reproduced 3 times. To reproduce Load at gate Power on aircraft (Battery, GPU) Import from Simbrief in EFB Init from EFB in MCDU Choose arrival for SCCI Click on ILS Y 25 System freeze Information Aircraft: A320neo Simulator: FS24 Navdata Method: NAVIGRAPH OFP: EGYP/28 DCT MTP UW54 GAL DCT EGOSA EGOSA2E SCCI/25 (see Simbrief PDF attached) Specs: NVIDIA GeForce RTX 4070 WASM: Error during FMGS_gauge_update execution. Error code : 0xc000001d EGYPSCCI_PDF_1763298577.pdf

Hi, Just reporting another issue this time in trying to fly from VABB to WMKK. MSFS2024, SU3. It's a 5 hour flight requiring 13.9 tons of fuel however if you try and enter the ZFW and Fuel load into the Inibuilds EFB, the ZFW loads correctly into the aircraft however the centre tank briefly loads with fuel as shown on the ECAM but is zeroed out again shortly afterwards (after 1-2 secs) meaning you can not fly with the full amount of fuel in the A320 NEO when trying to do more than 4hr flights (depending upon pax load of course)! Example: Enter the following values into the Inibuilds EFB then click Apply Load. ZFW=61284kg Fuel=13879kg Inste…

My joystick works perfectly fine, both in other aircraft and in the sensitivity window. Now in the a320v2, I get to about half way rudder input and it maxes out, you can see that the rudder pedals are still moving, but the ECAM shows that the rudder is fully deflected. I tried to taxi and it's very difficult, even though visually the rudder pedals are moving up and down all the way, the ECAM indication is how the plane actually feels. From halfway, even though the rudder pedals move, you get no additional steering... Is this a know issue or? I haven't found anything. Please tell me if I can fix it somehow or if it's something that needs to be fixed by ini …

Hi Guys, I have noticed that the anti-collision light is continuously illuminated, even when I have the beacon light set to the off position. Best regards, Max

Can anyone help me figure out how to shut down the APU using a mapped switch? Turning it on is no problem, using the mapping below. But switching the Master Switch to zero turns off the Master Switch light, but the APU keeps running merrily along. Any help would be appreciated.

Good Day, after updating navigraph avionics for msfs2024 but even before, SID and STAR are not working with Simbrief and without. You see it on my picture. From LSZH to EDDH isnt 6000 miles 🙂 Hope you find a solution. regards

In free flight and starting on departure runway, while wing lights, beacon, strobe, and runway switches are all visibly ‘on’ as switches on the overhead panel, the actual lights themselves are not on. I have to switch the switches all to off and then back on for the lights to work. Anyone else?

Good Morning all live started having a problem with the Airbus collection on MSFS 24 When I spawn in to an airport the GPU is not connected so I can’t perform any power up. I have tried toggling from EFB but no joy. Is this a bug or am I doing something wrong. Regards Craig

Hi, I wanted to let you know that when syncing the Simbrief OFP with the MCDU using the inbuilt EFB, the values in the Payload screen shown within the EFB are correct however when the sync with the MCDU is made and you move to INIT B of the MCDU, the incorrect CG value is loaded. On my MSFS2024 sim PC this is 100% reproducible and can also be seen in another person's YT video of setting up the MCDU in the A320 NEO. Look specifically for the time events in the video: At 18:45 where the OFP from Simbrief is synced, instant payload is selected and the values of 28.4% for the GWCG and 27.4% for the ZFWCG are displayed. At 31:55 you will see the MCDU ZFW/ZFWC…

Hi, I've just bought myself a new pc after having problems with lag on my old Xbox. Since getting my pc the graphics and scenery have been amazing, however there's one issue that after putting in my Simbrief id into the tablet and being able to request data and flight plans there , when i go into the MCDU and into the init page when i press init request it comes up saying "error downloading data" . My original thought was that i needed to important my simbrief id into the MCDU itself however after watching many videos they also said press the ATSU page and then you should see simbrief id. Which when i looked i couldn't see. I've contacted Microsoft support many times with…

I have this message and I don't know jhow to fix it. "Fuel ZFW ZFCG disagree"

Checking the initial FMGC page, A320neo has LEAP-1A26 engines and A321neo has LEAP-1A32 engines (which should provide more thrust), but the fuel flow in both idle and TOGA are exactly the same in A320 and A321. Can you provide a bit more insight what sources you used to model the engine parameters (thrust, fuel consumption, throttle response, etc.)?

Hello, This issue has alreaby been reported on the forum but not on the MSFS 2024 A20N section. So there you go. When entering the LFRS ILS-Z 03 page and clicking the arrow to see the next STAR in the list, all plane system freeze (at least AP, MFD and MCDU), but the sim continues to run, though the plane is unflyable after this system freeze. It just goes gliding down. If you want to replicate, start the plane at LFBO, import simbrief route and payload, in the MCDU go to LFRS arrival, select ILS Z03, click the arrow, and then you'll be stuck. No need to take off nor go further to replicate. But if you try it once in flight, you'll see it just glides down wit…

Hello, I experienced a WASM crash when I selected ILS Y for LFRS in the MCDU. It's the case at least for a320neo and a321LR. To reproduce : Load at gate in LFMN (didn't try other airports) Power on aircraft (Battery, GPU) Go to MCDU INIT page Type LFMN/LFRS Go to F-PLN page Select LFRS Click on ARRIVAL Choose any ILS Systems freeze Information Aircraft: A320neo (v2) & A321LR (at least) Simulator: FS24 Navdata Method: MSFS Navdata OFP: See above Specs: Ryzen 9600X, RX 7800XT, 32GB RAM Autosave: I don't have any autosave file WASM: Error during FMGS_gauge_update execution. Error code : 0xc000001d

Hallo liebes inibuilds-Entwicklerteam, ich fliege den A320 mit großer Leidenschaft im MSFS24. Für mich ist er das leistungsstärkste und beste Flugzeug im Simulator. Ich habe mir vor Kurzem die MCDU von Winwing gekauft. Leider funktioniert sie noch nicht mit dem A320 und A330. Bezüglich der Kompatibilität heißt es auf der Winwing-Website, dass sie auf die Freigabe des Entwicklers warten. Meine Frage ist nun: Wann veröffentlicht ihr die notwendigen Daten für Winwing, damit die Nutzer des Flugzeugs die MCDU nutzen können? Mit der FCU funktioniert sie bereits. Vielen Dank im Voraus. Viele Grüße.

Cruising along quite happily, I leave it flying to go and do some other stuff. But when I come back, it's flying in circles at FL400 in TOGA with the cavalry charge blaring. Sound familiar to anyone? Well I believe this is a feature rather than a bug but still one that perhaps needs to be addressed. In the real A320, if the speed suddenly goes outside of the safe band and into the red, this will cause autopilot to disconnect immediately. And this is fair enough as it means that something has gone wrong. But in MSFS, more often than not it simply means that the live weather has updated and the wind has changed direction So would it be possible to add a delay to t…

Everytime i am 100% sure and even double check any inibuilds aircraft doesnt follow my flightpath from my flightplan at all. I've been on many tutorials on how to fly the aircraft cuz maybe i did something wrong. there are no videos on why that is happening or how to fix that. Did this happen to any of yall and if so how did you fix it?