APPR Mode not activating in RNAV Approach after Update to 1.1.3

[skydiver6547]

I wanted to perform an RNP approach and activated the approach mode for this purpose. The brackets for the deviation of the LNAV and VNAV deviation did not appear and the aircraft did not start to descend at the intended point. In my opinion, something is wrong here. Unless I am mistaken, the logic worked before the last update.

[LineDX]

Same issue with CYYC RNP 17L. Did not capture virtual glide path 3' slope at 4800ft on final approach point. The pfd shows ILS app whereas FMS shows RNP approach. It was fine before this update.. 

[athiele]

Same here for LEPA RNAV 27R. 

[LineDX]

Tested with 1.1.4.

VGHS

Rnp 14 worked normal. 

Edited Saturday at 05:06 PM by LineDX

[Bianfable]

I don't think it's just RNAV. It seems every approach is broken right now, except ILS.

I tried an LPV approach (GCRR RNP 03-Z) and a GLS approach (LSZH GLS 14) and in both cases selecting the LS pushbutton showed ILS in amber on the PFD and pushing the APPR button also showed ILS, even though no ILS approach was selected. No guidance was available at all in both cases.

[frank_m]

I did today a flight to EDDM 26L RNAV approach. No issue. I'm using Navigraph Data in simulator as well as in the A350. 

[LineDX]

1 hour ago, Bianfable said:

I don't think it's just RNAV. It seems every approach is broken right now, except ILS.

I tried an LPV approach (GCRR RNP 03-Z) and a GLS approach (LSZH GLS 14) and in both cases selecting the LS pushbutton showed ILS in amber on the PFD and pushing the APPR button also showed ILS, even though no ILS approach was selected. No guidance was available at all in both cases.

Reinstall. Deleting the WASM files first. I had the same issue but after reinstall and wasm deletion did not see this issue. 

[Bianfable]

OK, thanks for the tip! I uninstalled, cleared WASM folder, re-installed 1.1.4, upgraded Navigraph data to 2508r1 und did some experiments:

• ✅ ILS: LSZH ILS 14 worked normally as always
• ✅ GLS: LSZH GLS 14 is fixed now and works again as expected
• ✅ SLS: LSZH RNP 14 with LPV works correctly
• ❌ SLS: GCRR RNP 03-Z with LPV does not work (no FREQ/CHAN filled, no guidance available)
• ☑️ FLS: LSZH RNP 14 with SLS deselected works in principle (F-LOC and F-GS arm correctly), but when activating LS pushbuttons it still shows SLS on the PFD (should be FLS instead)

Edited Sunday at 08:30 AM by Bianfable
add version

[skydiver6547]

I confirm, problem is solved with update 1.1.4.

[foliainfx]

41 minutes ago, Bianfable said:

OK, thanks for the tip! I uninstalled, cleared WASM folder, re-installed 1.1.4, upgraded Navigraph data to 2508r1 und did some experiments:

• ✅ ILS: LSZH ILS 14 worked normally as always
• ✅ GLS: LSZH GLS 14 is fixed now and works again as expected
• ✅ SLS: LSZH RNP 14 with LPV works correctly
• ❌ SLS: GCRR RNP 03-Z with LPV does not work (no FREQ/CHAN filled, no guidance available)
• ☑️ FLS: LSZH RNP 14 with SLS deselected works in principle (F-LOC and F-GS arm correctly), but when activating LS pushbuttons it still shows SLS on the PFD (should be FLS instead)

The ini doesn't support deselecting

[Bianfable]

2 minutes ago, foliainfx said:

The ini doesn't support deselecting

There is a button for deselecting SLS on the NAV RAD page and after pushing that I also got the expected F-LOC and F-GS indications instead of LOC and GS, so it's doing something...

[foliainfx]

8 minutes ago, Bianfable said:

There is a button for deselecting SLS on the NAV RAD page and after pushing that I also got the expected F-LOC and F-GS indications instead of LOC and GS, so it's doing something...

It does do something, but I've never seen it do it correctly