I've made a post or two in the discord community forum but here for officialness: 

Regarding WASM: 

• Upon entering the ANF menu to plan BTV exit: WASM: Exception c0000005 in gauge EFIS in module vfs://inibuilds-aircraft-a350/SimObjects/Airplanes/inibuilds-aircraft-a350-900/panel/inibuilds-A350.wasm
• Aircraft: A350-900
• Simulator: FS2020
• Navdata Method: NAVIGRAPH
• OFP: TURBU7S TURBU Y107 TOBSO DCT BAKOR DCT CHI DCT GOTMO DCT ALAXI DCT TEA DCT SOR DCT ROSAS DCT ADEXI DCT NIBLO/N0497F380 DCT ABRAM/N0498F370 N163 GRT A403 SHATI/N0491F390 A403 SEB M214 GARIN UG655 ILDOR UM214 IVDIG/N0485F410 UM214 OKLAP/N0488F400 UM214 ETMIT UZ35 ITROL UQ44 AVAGO AVAGO1D if related to FMS/Route Procedures crashes
• WASM Error: WASM: Exception c0000005 in gauge EFIS in module vfs://inibuilds-aircraft-a350/SimObjects/Airplanes/inibuilds-aircraft-a350-900/panel/inibuilds-A350.wasm
• Specs: Ryzen 7 5800X, RTX4070 and 32GB RAM.

Regarding FBW Rudder, NAV in Go Around, ground roll FMA glitching: 
https://youtu.be/Wc0fuUod4Qw

• FBW Rudder: Seems very commonly out of coordination during roll, with and without autopilot engaged. Can be seen quite clearly at the end of the video. 
• Lack of rudder coordination - sluggish turn rate and "delays" to input (I think this is what people are feeling without knowing its the adverse yaw).
• On Go around, the aircraft deletes the turqouise line and follows a weird track not sure where to, but definitely not the standard missed approach procedure that is associated with the approach just performed. 
• Additionally during ground roll, FMA freaking out between G/A, soft GA and roll out.
  https://youtu.be/Wc0fuUod4Qw

Hi @JonnyT1041

Thanks for your report. Shared with the team.

WASM Crash

Can you please specify the additional info that may help in reproduction of your issue

• DEP/ARR airports as well runways used. I'm assuming EDDM-FAOR based on routing but would be good to know for sure.
• Was the ANF active on both CPT/FO ND or only one of them?
• What was the active ND Mode (ARC/NAV/PLAN) when you set it to ZOOM or had the crash?

Thanks!

This was the panel setup when the crash had occured. 
EDDM-FAOR is correct. ANF only on CPT side. 
ND was set to ARC

 

Hi @JonnyT1041

Few of our testers have tried based on information provided and none of us could reproduce this WASM crash sadly.

In case you're able to have this consistently, or any other instance after selection of ANF, can you please share the latest autosave ".bin" file from before your crash?

Location for the autosave files can be found here: 

Thanks!

It might need to have the length of flight behind it. Will see if it occurs again but I'm not that keen on setting up 8+ hour flights with the intention of finding a wasm crash shortly before TOD 

Just do this or any other flight as normal. In case it happens again please provide the autosave as well as the WASM crash report as we'd love to resolve these issues however it is impossible to do without getting proper reproduction of it on any tester or production systems.

It is equally difficult to verify the efficacy of any fix implemented based purely upon "guesstimation" if we can't reproduce the errant scenario to test on.

Thanks for your patience and understanding!