Rene Feijen

I had the same. I knew already of the DH speed bug, but thought it was only optical, because we could also (hope to) rely on the blue line for set speed on the speed tape. But apparently the DH bug not only prevents showing a set speed but also actually setting a speed.

That is what I meant to say. From the gate I do pushback, and after pushback I wanted to taxi to the left, but it went right. THEN I did pushback again (on the taxiway, so strange /wrong place), as described above, and then I could use my rudder fully finally in both directions.

After about 25 flights without taxi steering problems, today , after pushback, I could only taxi steer -after pushback stopped- to the right with my TPR pedals. (although rudder pedals and tiller in cocpit turned left) . I pressed pushback STOP again , and a bit random again pushback straight and then pushed for a turn. Then STOP again... et voila... my rudders worked again for taxi steering. My 2 cents.

Aha... activating the approach phase on the FMCG. Never done that before. Cant remember seeing youtubers doing that but maybe overlooked? Will try.

A friend on mine (living in another country) practical always has autothrottle kicking in in the approach phase. I suspect his speeds are outside limits for normal (auto)land. Now I dont have this problem. Am I right to think that I first have to select a stage of flaps, thus allowing AT in PROF mode to let the speed go down, do a next stage of flaps, etc. And not the other way around: waiting for the speed to come down (which I would say will not happen in PROF mode but in some manual speed mode), and only then selecting flaps? Is somewhere in an SOP or FCOM described what to do in what order?

Thanks, nice to know, I have just started part 4 of my RPL MLA theoretical lessons, about Aircraft Aerodynamics and Performance.

I read in the A310 FMS Pilot's Guide: CG is displayed as a % of MAC [?] with a default value of 25%. If a trim tank is not fitted the field displays GWCG. With a trim tank it displays ZFWCG. Entry is mandatory to initialize the trim tank computer. I guess I will use indeed MACZFW. PS A guess: MAC = moment of aircraft?

I dont see a ZFWCFG I see MACZFW MACCGW and GWCG on the performance page. One is the same?

I had this starting to fall out of the sky but it was pilot error: I set a too high VS climb speed so the autothrottle could not manage the speed anymore, plane slowed down too much, began rolling to one side and AP disengaged. Managed within seconds to recover an engage AP again.

Since last update I can fill all INIT B fields automatically, except for the ZFWCG. I cant see this number on the performance page of the tablet, only MWCG. I just put in 30%, but is there a way to determine the realistic number?

BTW EGCC RWY23R KUXEM1R departure went well in PROF mode with NAV armed and on takeoff HDG mode 273degr and I think it autoswitched to D8.0 MCT. And EKCH LANGO2C departure also went flawless in PROF NAV mode.

I dont completely mind not to be able to AUTOLAND, but I DO mind not seeing the GS and LOC diamonds.. without them I cannot fly the ILS of course.

Yup, as always. (Now I did recycle the AP and LAND switches, but not the ILS mode selector. But... that should not be necessary in the first place). Also set on the copilot PFD and not showing the diamonds btw, as I tend to do long before I do that also on the pilot flying side.

1.03 Same here, no digits, but there was a moving blue line on the speed tape. All was good on 1.02. Also on ILS landing I did not see the GS and LOC diamonds on the PFD, although LAND was armed as I could see blue G/S and LOC indications on the PFD and PFD to ILS display set. Autoland did not kick in though, in spite of complete landing config and correct approach speed. That was on EHGG OLWOF1 arrival and then via HECTI ILS RWY23 approach. This also was good on 1.02.

I did one good approach without Navigraph, and then it failed again on the SID. So seems not to depend on that. Will continue testing. Maybe.