Soso330

Im not part of the ini team but this has been discussed on FBW's discord and also on GSX's support forum, the problem is MSFS in itself, the jetways always choose the closest door to the jetways starting position, i don't think there is much inibuilds can do about it, hopefully they can chime in it that isn't the case. In the meantime you could park the plane further forward so that the jetway is closer to L2 then it should connect to it instead of L1

Just tried the v1.0.1 update and all of these issues are still present. Found another thing regarding the "New" and "Old" display type option not saving, when you just started a new flight, you can see bezels of the dispays flicker, just like it's trying to switch display type or that it can't decide which option to use.

Hello Just tried the v1.0.1 update out and got a wasm crash on the winds page, restarted the sim and tried again and got it to crash again on the winds page. What i did: Start the flight, started external power first then the batteries, went into the OIS loadsheet page, requested the flightplan from simbrief. Went into the MFD, init page, cpny flight, insert flightplan, went into the winds page and requested the winds, went to the cruise winds, tried to request the winds again, went to the tray where you choose which waypoint to see the winds from and pressed on that thin little empty bar that comes down from that tray, closed that bar and opened that bar again and clicked on it again, and thats when the yellow pointer froze and i could'nt do anything in the MFD at all. Setup: Aircraft: A350-900 v1.0.1 Simulator: FS2020 Navdata Method: SIM DEFAULT OFP: LFBO/32L LMB6B LMB SIGOS 45N003W PEXOD DESAB SECHE SECH7N LFBO/32L WASM Error: WASM: Exception c000001d in gauge MFD in module vfs://inibuilds-aircraft-a350/SimObjects/Airplanes/inibuilds-aircraft-a350-900/panel/inibuilds-A350.wasm Specs: i7-14700K, RTX4080 Super, 64Gb DDR5 5600Mhz, 3x1Tb M.2 SSDs, 1000w Seasonic Focus plus gold PSU and Win 11 Home x64 24H2 Sorry missed the screenshot part and that you wanted the OFP in a PDF, hope it helps anyway. Kind regards

Hello inibuilds dev team I would like to make a suggestion to make the A350 save its fuel load after the flight, so that when you load into the sim at a later date it will start with the same amount of fuel that you left it with, much like the FBW A32NX and A380X does. i love that feature with the FBW planes, and would love to see your beautiful A350 do the same, it really adds to the immersion. Thanks for this beautiful bird and Kind regards

And right after starting this thread the sim froze for a minute or two and when it unfroze itself all of the GSX vehicles were gone and even the GSX menu on the OIS were gone, after disabling and activating the "GSX Integration" on the OIS and selecting "operate stairs" twice they came back. I know that this sounds like a GSX issue but i have flown with the FBW A380 countless times over the last couple of months and this issue was a first for me.

Hello, i've found a couple of issues. this was with the -900, haven't tested the -1000 but i guess they both run on the same code. Tested these things out twice with almost the same results. Display type settings in the OIS change by themself. I selected the "new" type of displays and after a session restart it showed that the "old" displays were chosen on the OIS, but the "new" ones were the ones that was actually showing, after another session restart they had also changed to the "old" just like what the OIS settings showed. GSX integration issues. First issue was that in order to make the GSX menu show up on the OIS on a session or sim restart i have to disable and then re-enable the "GSX Integration" setting even though i left the session with that setting enabled. Second issue was that when loading the plane with that GSX integration was that it loaded the cargo holds successfuly but added passengers aswell(about 8 of them), and when it started loading the passengers it also started to load extra weight in the cargo holds even though the cargo loading was already finished and the cargo doors were closed. Also it only loaded 140pax instead of the 318pax that was planned through simbrief using simbriefs own inibuilds A350 config. First test 140pax instead of the planned 318 -about 8 of them was before pax loading 4.1tons instead of the planned 8 -before pax loading 10.8tons instead of the planned 8 -after pax loading Second test 140pax instead of the planned 318 -about 8 of them was before pax loading 4.1tons instead of the planned 8 -before pax loading 21.9tons instead of the planned 8 -after pax loading Third issue was that in that same "loadsheet" tab on the OIS the "totals" never updated no matter how much cargo or passengers GSX added. Pax weights are only shown for First, Fwd Eco and Aft Eco, weights doesn't show under Premium Eco but pax amount shows on it. And for some reason during the first test door 2L didn't open for GSX but during the second test it did. Also during the second test the %ZFWCG on the loading tab went to 0 and stuck there. This is in MSFS2020 Kind regards

Hello I've noticed that even when after a flight when setting passenger and cargo weight to 0 and pressing the realistic loading the unloading is instant, could you enable it to recognize unloading aswell? Or more preferably add a seperate button for unloading realisticly? Or is a full gsx integration with full refueling, loading and unloading on the horizon? Either way it's a small addition that greatly increase immersion.

Hello I've noticed that even when after a flight when setting passenger and cargo weight to 0 and pressing the realistic loading the unloading is instant, could you enable it to recognize unloading aswell? Or more preferably add a seperate button for unloading realisticly? Or is a full gsx integration with full refueling, loading and unloading on the horizon? Either way it's a small addition that greatly increase immersion.

Thank you! Yeah its like the EFB loads a payload without even knowing it, as it clearly says 0kg payload/cargo weight, BUT a payload is showing in the hull and if you take the current weight minus the fuel weight you see that it has accounted for that weight of the "not loaded" cargo giving me a zero fuel weight of 351tons so a weight of 66+tons has been added as cargo while having "0kg cargo/payload weight" added.

But the thing is that the an225 does not behave like all the other planes when setting the payload before loading in, all the other planes(default and addon) you can set the payload and it keeps it when loading in, but with this plane you can set it to 0 and it resets the weight back to 49999kg for the "cargo main deck", i get a feeling that it might actually be a bug with the EFB because something is overriding the Default MSFS payload window. After loading in: Looking at the EFB it says that the payload is 0kg, but i have to press "unload payload" or "apply load" for it to actually be 0kg

Awesome! thank you!🙂

Hey this is 2 screenshots taken right after i loaded in. Is there a way to have it load in empty? Also preferably with about 20% fuel About the camera, hopefully Asobo will fix it then Kind regards

Could you make it so that the plane is empty when starting a new flight? right now the plane is already loaded with 66tons when starting the flight Also the cockpit viewpoint does not follow the cockpit down when the aircraft is kneeling to loading configuration Kind regards