pmplayer

On newest A350 build ( 1.1 ) At a last flight landing at OMDB ( inibuild ) and traveled to my Gate and there goeing to shot of my engines. After reaching my gate i would goeing to shot of my engines which i did with the two cut off levers at the pedalstal but the engines did not go off so i tried to load a panel save ( APU and or at GPU ) but this didn`t work either - no engine shot down so what.. ?? 🤣 Bug or WASM crash ?? Help..🤪 cheers 😉

By the way: Turbulence in MSFS2020 does not show off - it says "low, middleway,realistic" so i will try low. So yours ( Chris3DX ) should at least have "low" ?? cheers 😉

OK, thanks, i will try the new 1.1 build with Turbulence off and see if the ILS path goes better than.. cheers 😉

OK Thank you, found it in the PREF page and this looks normal now to me.. About the Glideslope, what Turbulence settings are you using ( MSFS2020 ) as far as i know there three different one - Normal, middleway and realistic. I am using middleway and i saw on GL path strong and fast changes from the wind dir so could be better on "normal" but with this setting you see almost no wingflex and thats odd.. cheers 😉

Where can we set this ? Thanks.. cheers 😉

Furthermore I can't believe that such a new airplane needs 150nm at 31000ft altitude (and that with 195.000kg which is almost 100.000 less than max), so I think the climb performance is clearly too weak ! cheers 😉

Hi guys, That said I realy did a lot of flighs with older builds and the Autoland works realy well, but with this new build it dosent work as before ??? The story begins at around 1500 to 1000ft ( plus-minus ) before the landing Airport runway ( that sayed LOC seems fine ) the GS pointer goes down fast and the AP tries to catch the pointer what brings the speed of the plane up high so the plane goes up and down trying to hold GS what ends in a jumping bag and so the plane hits the runway like a stone and you just can`t do nothing if you don`t shut off AP and AT and handle it your self - but that could be the thing from an Autoland !! I did a same flight wtih a saved build 1.0.10 and had a beautful Autoland, so please inibuilds check that code something is wrong or changed somehow so no normal Autoland can be done with the new build.. If anyone has similar experiences with Autoland please post here - thank you ! cheers 😉

OK found thre Problem, it was a start from the Runway and therefor you have to look under the CDU Active - sec init page there you can import the plan and insert them. cheers 😉

Hi all, At my first flight today with the A350 i set up a flightplan at Simbrief, my Simbrief ID is showing in the EFB settings so this should be OK. Over the EFB i could do all what is needed to load the SIMBRIEF Flightplan into, so all was seen, OFP, Sync Simbrief, and so on.. But on my CDU ACTIVE at the init Page my CPNY F-PLN REQUEST was greyed out and so i could not load the PLN into the CDU. I tried serveral times with restart the flight and close the Sim and started new but i had no luck, the request always was greyed out so seems i need some help here. Someone else seeing this or do i forget some settings for that, so a bit confused here.. Any help would be nice !! cheers 🙂

But this Asobo weather Radar is better then none, at least for me.. cheers 😉

I have not seen or hear a loss of ATC Voices.. cheers 😉

So you can use the CDU over network with an Tablet or a Handy. Any chance of that ?? Would be great, i have that for the PMDG777, PMDG737, Leonardo MD82 ect. so a great Funfaktor more in Flightsimulation.. https://www.aviaworx.com/aviacdu cheers 😉

What build Version of the plane ? Do you use the newest V 1.1.2 ? cheers 🤔

Is there coming one soon for the A300-600 ? cheers 😉

Just to reply back, ( i had bad problems from Version 1.0 until to 1.1.0 ) i did three other flights ( 3 to 5h ) and all oft them went well, seems pretty stable now with V.1.1.1 ! cheers 😉