Whenever I select a different page on the SD I get the R INR TK AFT PMP FAULT message on the E/WD and yes when I check the overhead the pump is off.

Any idea why this would be happeneing?

10 minutes ago, balus said:

Whenever I select a different page on the SD I get the R INR TK AFT PMP FAULT message on the E/WD and yes when I check the overhead the pump is off.

Any idea why this would be happeneing?

Did you turn the pump off because of the fault message or was it already off?

1 minute ago, sultan.of.swing said:

Did you turn the pump off because of the fault message or was it already off?

All pumps were on before I selected the different page on the SD - as soon as the new page is displayed the pump turns off and the message appears. Turning the pump back on via the overhead clears the message.

Hi,

Wondering if there is a keybind issue somewhere. I have not heard or seen any other reports of this behaviour.

If you're able, could you please attach a short video showing this happen?

Thanks!

8 hours ago, iniKyle said:

Hi,

Wondering if there is a keybind issue somewhere. I have not heard or seen any other reports of this behaviour.

If you're able, could you please attach a short video showing this happen?

Thanks!

I doubt it's a keybind as I am only using mouse clicks, not keys or buttons. I'll see how it goes with flight number 2...

59 minutes ago, balus said:

I doubt it's a keybind as I am only using mouse clicks, not keys or buttons. I'll see how it goes with flight number 2...

Just starting flight #2 and it is reproducible. Engines not started, external power connected, APU starting, select ENG page and the pump goes off - turn it back on, select any other page, same outcome, the pump goes off.

EDIT: Even selecting T/O CONFIG turns the pump off, basically any button on that panel will turn the pump off. Mouse clicks on any other location seem to work fine.

Edited yesterday at 12:35 AM1 day by balus

4 hours ago, balus said:

Just starting flight #2 and it is reproducible. Engines not started, external power connected, APU starting, select ENG page and the pump goes off - turn it back on, select any other page, same outcome, the pump goes off.

EDIT: Even selecting T/O CONFIG turns the pump off, basically any button on that panel will turn the pump off. Mouse clicks on any other location seem to work fine.

Hi,

Just tested this on my end and everything is working as intended. I've cycled through every options on the E/WD, including the T/O config button.

Before we go into more troubleshooting steps, have you downloaded the aircraft or are you streaming it?

Thanks!

37 minutes ago, iniKyle said:

Hi,

Just tested this on my end and everything is working as intended. I've cycled through every options on the E/WD, including the T/O config button.

Before we go into more troubleshooting steps, have you downloaded the aircraft or are you streaming it?

Thanks!

I have downloaded it

8 hours ago, balus said:

I have downloaded it

Ok, I believe that may be the issue. If you can, uninstall the aircraft and stream it. That should solve the issue.

Thanks!

6 hours ago, iniKyle said:

Ok, I believe that may be the issue. If you can, uninstall the aircraft and stream it. That should solve the issue.

Thanks!

I'll test this later today, but I will be disappointed if this is the cause, I prefer my aircraft and scenery downloaded, mainly for performance reasons.

Nope, uninstalled, confirmed streaming in the marketplace - load aircraft, align IRS, started APU, the SD showed the APU page with the flap open but then reverted to the Door page. Loaded Simbrief flightplan, configured FMC, went to check another page and the same pump turned off.

EDIT: Once the engines are started I get the message on the E/WD and an aural indicator, checking the overhead, the pump is off. If I click on the CLEAR button that is highlighted on the SD controls, then the pump turns back on and the message clears.

Edited 6 hours ago6 hr by balus

10 hours ago, iniKyle said:

Ok, I believe that may be the issue. If you can, uninstall the aircraft and stream it. That should solve the issue.

Thanks!

I dont understand this download vs stream thing, I got it on the store in-sim and it downloaded?

Just now, DJSean00 said:

I dont understand this download vs stream thing, I got it on the store in-sim and it downloaded?

Neither do I, are you having the same problem?