Inibuilds A350 Master WASM Crash Thread v1.2.4 FS24

[Lucstra]

WASM Crash Report – iniBuilds A350 (FS2024)

I encountered a WASM crash after vacating runway 25 at EDDS following a diversion caused by a dual engine shutdown.

Flight Details:
Route: LFPG 26R BUBLI6A BUBLI DCT LUVAL DCT MIRGU DCT BEGAR DCT TRA DCT GAMSA DCT UMVEG DCT DIMLO/N0485F350 DCT INVED DCT DINRO DCT UDROS UM859 KARDE UN644 ROLIN DCT TETRO DCT BARAD M747 SUBUT T916 LEYLA/N0499F370 N161 GASBI/K0919F370 N161 SARIN/K0889S1130 A368 SALMO/K0885S1190 A368 FKG W188 LIKMI W270 DKO W69 HUR B339 LADIX W34 VAPGU W100 ORAVA W201 UNSEK A326 SANKO/K0906S1250 A326 DONVO G597 AGAVO/N0487F410 Y644 EGOBA G597 LANAT Y71 XAC XACL RJTT16L
Aircraft: iniBuilds A350-900 v1.2.4 (with cabin)
Simulator: FS2024
Navdata: Navigraph

Issue Description:
A dual engine shutdown occurred unexpectedly between LUVAL and BEGAR. I initiated a diversion to EDDS via REUTL5A arrival for runway 25.

After landing, I disconnected the autothrottle at approximately 50 knots to vacate the runway via taxiway I. The WASM crash occurred during runway vacating.

Error Message:
WASM: Module vfs://inibuilds-aircraft-a350/SimObjects/Airplanes/A350/attachments/inibuilds/Function_Interior_A350/panel/inibuilds-A350.wasm is now dirty
WASM: Error during MFD_gauge_update execution. Error code: 0xc0000005

System Specs:
Ryzen 7 9800X3D, RTX 5070 Ti, 64GB RAM

1775397464.bin

[Thyra7]

On the ground at LHR. 

MSFS SU4, latest A35K version. 

During cockpit preparation, adding the TRANS / VIA for KLAX crashed it immediately, turning all displays orange.

 

 

[Thyra7]

10 hours ago, Thyra7 said:

On the ground at LHR. 

MSFS SU4, latest A35K version. 

During cockpit preparation, adding the TRANS / VIA for KLAX crashed it immediately, turning all displays orange.

 

 

During flight adding a complex arrival no issue. Seems to be an issue during pre-flight heavy loads.

[Sirraj]

WASM error occurred when I attempted to change the arrival runway during cruise.

Thank you.

• Aircraft: A350-900 
• Simulator: FS24
• Navdata Method: NAVIGRAPH
• Specs: Ryzen 7 9800X3D, AMD RX7900XT, 64Gb DDR5 6000 RAM 

KSFOKLAX_PDF_1775657462.d434bc26.pdf 1775656981.bin

[lucianoo__]

• Aircraft: A350-900 (no cabin)
• Simulator: FS2024
• Version: 1.24 
• Navdata Method: NAVIGRAPH
• SPECS: i9-9900k, RTX3070ti, 32GB RAM

WASM crash after switching frequencies. Last thing I did was dial in / type in the frequency and then switch to it on the RMP. the RMP WASM gauge also failed. If this is any relevant to the case, I was connected on VATSIM. 

As I now found out the location of the autosave files, this time I attatched two autosave files (each 10 minutes apart, one of those should be just before the crash I hope.). 

1775694645.bin 1775694041.bin

Edited 11 hours ago by lucianoo__