This update can be downloaded via the iniManager.

v1.1.6
Fixed: Numerous system crashes
Fixed: Sim freeze when selecting LFRS - ILS Y RWY 03, Transition NEDAN for VALA1C
Fixed: Sim freeze when selecting  LSZH ILS 28
Fixed: Code crash when entering STAR with transition
Fixed: Default key bindings "ON" / "OFF" not working for light switches
Fixed: WASM, freeze when entering SEC F-PLN 
Fixed: ND Blue Alt arrow shown in HDG/S & V/S descent along with yellow banana
Fixed: INIT B - TOGW is not affected by TAXI fuel change
Fixed: C&D Spawn at Gate - Dome/Emergency Light on by default
Fixed: Rudder trim panel knob operation reversed
Fixed: AP Disconnect switch missing sound
Fixed: Gear suspension limits tweaked for a more realistic aircraft stance on the nose gear
Fixed: flood light on in cold and dark state

This update can be downloaded via the iniManager.

v1.1.4
Fixed - Random Crash - Fuel runs out
Fixed - SEC F-Plan crash
Fixed - VNAV Issues - Descending too early / capturing speed target too early
Fixed - EFB Door Arming Logic / Option Reversed
Fixed - APU keeps running if start is aborted
Fixed - FMS Progress Page VOR/DME Station behaviour & formatting
Fixed - THR and ACCEL altitude logic and behaviour

v1.1.3 of the iniBuilds A300-600R Airliner for MSFS has been released. This update brings many fixes and also compatibility to MSFS2024! Take a read through another extensive changelog below!

Please note, this version does not include the additions and changes that have been introduced for the A300-600R Premium for MSFS2024, you can find more information on this -> here.

This update can be downloaded via the iniManager.

v1.1.3
Art
Fixed - Gap behind rain rep panel 
Fixed - Z-Fighting near PEDESTAL LIGHTING knob (only with IDC Radios)
Fixed - TRP decals floating above model

Systems
Fixed - [VNAV] DECLL level distance seems too short putting me ILS at 240kts for 3 approaches tried 
Fixed - [RW Pilot Feedback] FU showed incorrect figure in flight
Fixed - EPR/N1 Throttle position indicators on EPR/N1 gauge with engines of
Fixed - Preset speed in descent behaviour
Fixed - TOD Disappeared after DIR TO whilst on HDG SEL, then selecting NAV to resume navigation
Fixed - IMM DES not respecting FCU Target Altitude 
Fixed - Cabin pressure control system does not take into account landing field elevation
Fixed - [AFS] Phugoid oscillation during AP ILS - multiple user reports
Fixed - Random Crash - Fuel runs out - Video / User Report
Fixed - VNAV Issues - Descending too early / capturing speed target too early
Fixed - WASM CRASH - XBOX - Request Winds 
Fixed - SEC F-Plan crash
Fixed - [IDC] Some Hoppie messages severely delayed
Fixed - FMS Progress Page VOR/DME Station behavior & formatting
Fixed - [ECAM] Oil Delta T mirrored on both engines
Fixed - [ECAM]  "NORMAL" message frozen after recall
Fixed - [ND] WXR Image does not change with range
Fixed - Weight prefilled in RC7, ZFW 212.5, ZFW CG 27%
Fixed - C&D - WINDSHEAR aural alert played when ANN LT switch set to Test, event without any power
Fixed - INIT B is pre-filled on spawn at gate
Fixed - In-game ATC has no voices
Fixed - IRS 2 Overhead warning - not going into ALIGN mode
Fixed - [AFS] P.DES does not arm when conducting RNAV APPCH (NAV+P.DES)
Fixed - [AFS] Acceleration at THR RED instead of ACCEL alt
Fixed - WASM Crash - VHHX (Dep or Arr, doesn't matter) + wind data 
Fixed - [ECAM] OIL Temp doesn’t come down after engine shutdown
Fixed - WASM Crash - ALTN airport data 
Fixed - VOR jumps around in PLAN mode
Fixed - Doors warning ECAM inhibition Logic - APU SD Page not shown automatically when doors are open

EFB
Fixed - [PERF CALC] Landing Distance longer with 30/40 vs 15/20
Fixed - INIT B - ZFW Autofill does not match EFB ZFW
Fixed - Door Arming Logic / Option Reversed
Added - TO/LAND Perf Calc - Runway Selection menu sorting improvement
Fixed - Maintenance - "Finish now" not working with Service Engine 2

This update can be downloaded via the iniManager.

v1.1.2
LNAV 
Major overall system rewrite to better handle turns into initial fix and SID/STARS and holds.

Systems

New improvements:
1 - bleed PSI should be +/- 30psi during start
2 - LO OIL PRESS should be on at fuel lever on and ECAM oil pressure should be red, until 70PSI (goes out and goes green at 72PSI)
3 - engine generators should come online at 52% N2, not 49%
4 - Overhauled PW start sequence following feedback from real A300 pilot
5 – Optimisations to increase performance
6 - ENG FADEC CHANNEL 1+2  FAULT – ECAM logic [Feedback from real A300 pilot]
7 - Significant improvements to stability with WASM crashes and CTD

Fixes:
Fixed - WASM Crash on SEC-FPLN Deletion/Activation 
Fixed - WASM crash doing right turns
Fixed - WASM Crash on exiting Hold - EGSS ILS04 at ABBOT 
Fixed – WASM crash related to terrain radar 
Fixed - WASM crash when entering ZFW
Fixed - SD Wheel Page - Green/Orange overtemp Arc showing around wrong wheel
Fixed - Engine/APU Fire test logic corrected to match RW flow 
Fixed - N1 Command/TLA Position Needle in wrong position during REV THRUST
Fixed - When on glide aircraft can't be controlled
Fixed - IRS mode and source selectors missing interaction
Fixed - EFB remains off until Ext Power connected
Fixed - If ISOL valves off fuel line is drawn between ctr and outer tanks
Fixed - Showcase camera views
Fixed - Quick views R and L view corrected to 90*
Fixed - 3 max waypoints loading on AIRWAYS
Fixed - ECAM FUEL Page - Right Inner fuel feed line not drawn 
Fixed - Throttle Calibration not working (Throttle input not detected) 
Fixed - TCAS traffic INOP
Fixed - FCU Speed reverts to IAS when cruising in MACH mode once TOC is reached
Fixed - Flight perf feedback – refined overall flight performance
Fixed - Trim wheel missing integral lighting
Fixed - Shutdown Checklist
Fixed - FO Alt gauge OFF flag black pixels
Fixed - FUEL SD page and left ECAM MEMO page updating at different rates
Fixed - Fuel Pred - Pressing Fuel button in flight erases values
Fixed - IRS Alignment logic 
Fixed - Direct to logic – Now allows for direct entry change
Fixed - VNAV Climb logic 
Fixed - FMA/FMGS Logic 
Fixed - MDCU Perf page logic
Fixed - MCDU F-PLN page - END OF F-PLN stuck on L2
Fixed - Trim wheel set to 1.0NU, but when adjusting with key controls it snaps to 0NU
Fixed - Speed targets in FMS don't match what PROF commands
Fixed - TACT Mode logic
Fixed - PROG - FUEL PRED PAGE - Altn airport EFOB showing as "-N<-N"
Fixed – Holds adjusted to follow magnetic course
Fixed - ECAM - TO Mode
Fixed - STBY Horizon lost alignment after landing when the APU on
Fixed - Changing descent winds forecast does not affect T/D prediction | BTG
Fixed - Engine Start Sequence logic
Fixed - ND Config logic
Fixed - ND Display logic
Fixed - MDCU perf page logic
Fixed - FD1 annunciation disappears from PFD
Fixed - FMA modes logic corrected
Fixed - BRK TEMP HIGH ECAM message not clearing when Brake Fan selected
Fixed - MCDU flight plan display
Fixed - Assigning a button to control brakes causes conflicting command
Fixed - Secondary flight plan on the ND should be blue
Fixed - "500" Callout on Takeoff in pax variant
Fixed - Oil temp not rising fast enough
Fixed - FLT CTL page missing title
Fixed - FPLN Page - unable to input Lat/Lon as a fix
Fixed - Erroneous T/D
Fixed - Scrolling through F-Plan should be one wp per arrow press
Fixed - CTD When loading into plane (FLY NOW button)
Fixed - Rudder should still turn nosewheel by 6°
Fixed - MCDU F-PLN page additions and corrections
Fixed - ND Runway length filter for fields under 5000' length (may sometimes return smaller fields based on sim logic)
Fixed - Plane stalls in VS mode when trying to hold a pitch below stall speed. Aircraft will now pitch down
Fixed - Airway L620 not returning fixes on FLT plan page
Fixed -  T/O Perf calc page hPa/inHg tied to WEIGHT UNITS option in settings
Fixed - Weight & Fuel changing mid-flight, then FU bugged and SBY Horizon bugged
Fixed -  Loss of systems after returning from pause
Fixed  -Systems and display freezing - LSGG-LFSB with the LUMEL 8K arrival, ILS Z 15 approach.
Fixed -  CTD - KLAX star ANJLL4 via DNERO transition, ILS 25L via CRCUS
Fixed  -Speedbrakes show as deployed on ECAM on spawn in
Fixed - No Flex temp on TO calcs with PW
Fixed - BUS 1 should be connected to ESS BUS, GEN OVRD should have an arrow [Feedback from real A300 pilot]
Fixed -  Landing distance calculator bug fixed 
Fixed - Elapsed Timer does not show "1" in 10h02m ET
Fixed - Fix landing distance calculator (in current state, the METAR data does not sync)
Fixed - T/o Perf calculator does not mirror altimeter units from settings
Fixed - Eng Fire squib test still shows in Amber
Fixed - [EFB] MTOW discrepancy on TakeOff Perf Calculator
Added – You can now have a custom background on your EFB
Fixed - FMS: Distance to T/D should report actual distance and not distance between last w/p and T/D (distance between last and to should be actual distance, not segment distance between waypoints. [Feedback from real A300 pilot]
Improvement – Overhauled Packs off operations following feedback from real A300 pilot
Fixed  - ILS freq selection: Only ILS freqs should be avail – uneven after “.” E.g.10/15/30/35…) .20/40/60 are not valid ILS freqs [Feedback from real A300 pilot] 
Fixed - ECAM logic on start [Feedback from real A300 pilot]
Fixed -  ECAM Brightness panel labels disappear when IDC Radios selected from EFB
Fixed  - MODE CHG stuck on ND
Fixed  - RMI Gauge VOR bearing/declination issue
Fixed - Eng N1 should show until +/- 1% on shutdown
Fixed - IMM EXIT prompt bug 
Fixed - MCDU: PROG page - cannot return out of ENG OUT mode
Fixed - FCU lights disappearing in flight (daytime)
Fixed - Simbrief weights bugs
Fixed – TOD ETA incorrect 
Fixed - Winds have no effect on INIT B or FUEL PRED page
Fixed - TRIP TIME and fuel burn predictions exaggerated
Fixed  - FACT RWY19 TETAN 1A SID
Fixed - FMS: OPT and MAX FL’s are in steps of FL005 [Feedback from real A300 pilot]

Art

Fixed - All outside animations and cockpit yoke tiller animations running at 5/10 fps
Fixed - Stairs don't spawn on freighter
Fixed - Backpanel  APU EGT, N1 and OIL gauge needles not lit at night
Fixed - EGT warning light on GE engine config lighting up at PW limits
Fixed - Oil QTY bugs animation no longer as smooth as before
Fixed - Hole in rear of GE model (Checked all liveries)
Fixed - FO TERR MODE GPWS decals missing
Fixed - Floating fan blade numbers PW DHL (D-AEAF)
Fixed - D-AEAF red texture line floating when bulk door opened
Fixed - Reversed text on tyres when worn
Fixed - Fuel Pressure Indicator Window missing on liveries
Fixed - [XBOX][ART] Double edge around windows (and no textures)
Fixed - L/R Stairs not showing when selected from EFB

Sounds

Fixed - External airport ambience sound adjustment
Fixed – Various overhauls and minor tweaks 
Fixed - Allow warnings/callouts/alerts volume to be controlled separately
Fixed - Trim “Whooler” sound missing
Fixed - APU external sounds 

EFB

Added can now create a custom background. Instructions here: 

-----

v1.1.1 of the iniBuilds A300-600R Airliner for MSFS has been released. This update fixes lots of different items from systems, to art, sounds and more! Take a read through the extensive changelog below!

This update can be downloaded via the iniManager.

v1.1.1
Systems

Fixed - [VNAV] When in the turn VDEV reporting low on path but ending high after turn complete 
Fixed - [SYS] When pressing N1 mode no ECAM is shown
Fixed - [ENG] OIL TEMP to not be based on EGT
Fixed - Double pressing +/- on IDC doesn't' switch between a + and -, just inserts + every time 
Fixed - [IDC] AOC Enroute - Pos Rpt unable to change fuel from KG to LBS, regardless of units selected on EFB
Fixed - [IDC] Squawk IDENT on ATC/TCAS CONTROL page doesn't send ident command to Vpilot
Fixed - F-PLN B page when RSK should take to VERT REV B page also
Fixed - [IDC]TCAS "TA ONLY" state doesn't show an indication in the TCAS control page
Fixed - [SYS] ECAM TCAS STBY memo does not appear when ALT RPTG ON
Fixed - [SYS] No Bleed air pressure indication with APU Bleed ON, ENG OFF
Fixed - [SYS] Bleed air pressure gauge gets stuck to last value when R ENG BLEED = OFF
Fixed - Can't step through ATLN/SEC F-PLNs
Fixed - BRG/DIST should be to 1 decimal place
Fixed - TO Config should read NORM FOR T/O
Fixed - TCAS showing traffic at wrong relative altitude
Fixed - STAR selection code crash
Fixed - EFIS dials (DH, FPA) can be adjusted with FCU off
Fixed - F-PLN B page wind format 
Fixed - [FMGS] Speeds in plan do not account for transition alt
Fixed - [ENG] N2 speed during crank
Fixed - Manual changes to INIT B should be big font
Fixed - Pressing GPWS switch when alert is active does not cancel warnings
Fixed - PACKS OFF Operations
Fixed - AP/AT Disconnect switches not animated via control input
Fixed - [VNAV] Aiming for CST too early 
Fixed - If a message is open on one idc, sending a message from the other messes with the message displaying IDC
Fixed - ORIG/DEST have no input sanitisation
Fixed - Switching panel button behaviour
Fixed - Should be possible to modify sps/alt/wind dir/temp directly on F-PLN
Fixed - Should be able to dial in a speed when in PROF like in the A320 for when you switch to LVL CHG or VS
Fixed - Unable to change LAT/LON with slew keys INIT A
Fixed - Navaid/REF pages
Fixed - MCDU F-PLN page additions and corrections
Fixed - IMM DESC is started with any right LSK on F-PLN page
Fixed - Des arrow is few pixels off again
Fixed - Wrong bearings on SID (FACT RWY19 TETAN 1A SID)
Fixed - Tiller getting stuck left when used via rudder axis
Fixed - [IDC] COM Presets not saving either Com1 or Com2
Fixed - Throttle locks to idle after turning off autothrust
Fixed - [SYS] CTD/Plane stops responding when deleting HOLD/Waypoint from PROC in MCDU
Fixed - Should be possible to modify sps/alt/wind dir/temp directly on F-PLN
Fixed - ENG 2 PW EGT max pointer needle doesn't move
Fixed - MCDU F-PLN page additions and corrections
Fixed - Wrong bearings on SID (FACT RWY19 TETAN 1A SID)
Fixed - PFD errors
Fixed - Oil level mismatch on PW variant
Fixed - FMS number rounding
Fixed - ANTI SKID release indicators in flight on the wheel page are missing
Fixed - Door SD Page improvements 

Art

Fixed - Cargo compartment smoke detection switch animation issue
Fixed - APU exhaust still visible after being shut down
Fixed - Missing GPWS Landing Flaps/ Slats selector switch text
Fixed - [ART] Using the IDC panel - lose the lettering and the illumination around the ILS and VOR frequencies
Fixed - [ART][PW] Eng 2 EGT Orange Needle INOP
Fixed - [ART] Weird shadow on IGN/APU panel buttons
Fixed - EGT warning light on GE engine config lighting up at PW limits
Fixed - [ART] FO/CAPT switching lower sys indications should be boxed
Fixed - Squib emissive should be white, not amber
Fixed - [ART] FO Switching panel has red lines on buttons when CAPT side switching is set to SYS3
Fixed - Engine 1 Pylon labels mirrored
Fixed - [ART] PW Pax house livery on the nose says Freighter (600RF instead of 600R)
Fixed - [PW] Pilots Model missing from external view
Fixed - Cabin light resets when zooming out

Sounds

Fixed - GPWS test plays in C&D 
Fixed - Alt alert C chord cuts off early if you rapidly adjust the alt knob on the ground
Fixed - [SOUND] Exterior view engine sounds fade in and out
Fixed - PW sounds on fuel injection
Fixed - Increase ATC COM telex volume
Fixed - RA Callouts playing on panel state change
Fixed - Horizontal Stabilizer Trim animation inverted
Fixed - Engine sounds disappear too fast on shut down
Fixed - Sound Mix Feedback

EFB

Fixed - Pax EFB has toggle catering option avail in the air
Fixed - [EFB] On-screen keyboard only shows numbers for HOPPIE field on settings page
Fixed - [EFB] Enroute map - save/retain zoom level when switching between EFB apps
Fixed - Landing calc RWY graphic units not syncing

Other

Fixed - MSFS Checklist TOGA highlights old ATC COM button click spot
Fixed - CPT PFD brightness typo

This update can be downloaded via the iniManager.

v1.1.0
New Features
Added – IDC modern radio panel with CPDLC and ACARS systems and sounds
Added – PW passenger and freighter variants with unique systems and engine sounds
Added - Navigraph enroute moving map functionality
Added – EFB Landing Distance calculation performance page

Bug Fixes

Systems
Added - Speed mode preselect
Added - Better VNAV profile descent implementation
Added – Now possible for FMC to not reset when changing panel state
Added - Decel mode
Added - FMC to not reset when changing panel state
------
Fixed - APU ECAM shutdown logic
Fixed - Throttle goes into idle on bumpy runway
Fixed - VNAV issues
Fixed - Inhibit A/THR -> MAN THR reversion during TO phase
Fixed - HYD levels not the same on OHP and ECAM
Fixed - There is no connection between compressor rotation and temperature rate in crank mode
Fixed - ND Drawing issues
Fixed - 3.00° missing in fpl during RNAV approach
Fixed - Speed constraint not taken into account
Fixed - Oil runs out even though the maintenance options is off
Fixed - APU not starting
Fixed - VS does not sync with current climb/des rate
Fixed - APPR page info doesn't clear if you have done an RNAV
Fixed - Flex derate does not modify EPR on display
Fixed – Throttle calibration issue Thrustmaster Boeing Yoke
Fixed - Throttle2_cut sets thrust to 50%, Throttle1_cut works as expected
Fixed - Inhibit A/THR -> MAN THR reversion during TO phase
Fixed - Speed mode preselect
Fixed - Temps going to -56° in cockpit/cabin after starting the descent
Fixed - AI copilot can't change transponder code
Fixed - VOR mode stays in VOR* even though the VOR track got captured
Fixed - Cannot enter custom RTE RSV, immediately changes back to default value
Fixed - ADF flickering
Fixed - Throttle goes into idle on bumpy runway
Fixed - VNAV profile descent implementation
Fixed - VNAV pathing
Fixed - Typo in aircraft.cfg files
Fixed - Throttle issue, exclusive to the Thrustmaster Boeing Yoke
Fixed - Rad alt call seems off.
Fixed - Similar to the two TCAS tests, there are also two GPWS tests
Fixed - Auto Checklist injects fuel instantly, leading to hot start, A310 checklists waits till 20% N2
Fixed - Max Pointer reset no TT
Fixed - APU oil looks to have overflowed

EFB
Added - Allow "My Flight" page to pull info from FMGS when user hand codes flights without Simbrief
Added – better EFB descriptions
Added - Realistic Door Cargo Door Speed control to settings
------
Fixed - Make checklists, flightplan and OFP click and draggable
Fixed - Altimeter unit always in hPa on performance page
Fixed - OFP formatting issues
Fixed - En-Route Map is possible to click the Leaflet link on the bottom right

Sounds
Added – PW sounds
Added – IDC sounds
------
Fixed - Left engine balance not correct vs right engine from pilots seat
Fixed - No ADF/NDB identifier tone
Fixed - Abrupt change in engine sounds during start up
Fixed - Missing button sounds
Fixed - Brake fan sound remains when MSFS is not in focus
Fixed - No landing sound effect
Fixed - Sound several events
Fixed - Flaps motors too quiet in wing view
Fixed - Main Cargo Door missing sound (was there ever a sound?)
Fixed - ALT HLD sound switch plays when FMA mode changes

Art
Fixed - Horizontal Stab not moving with THS setting
Fixed - Reverser Sleeves animation should fully extend as soon as reversers are open - Does not correlate to thrust setting
Fixed - Pallets clipping
Fixed - No integ lighting on brightness buttons IDC
Fixed - Altimeter gauge flickers
Fixed - Duplicated text on overhead
Fixed - DC Voltage gauge showing jumpy animation
Fixed - Reg decal overlap
Fixed - N2 gauge indications

This update can be downloaded via the iniManager.

v1.0.9
- Update to spoiler arming code
- Fixed EFB parsing potential null value when fuel divided by 0
- APU EGT not resetting to ambient temp over time and apu fx still visible after shutdown
- Temporarily removed EFB reg/selcal in cockpit option
- AP2 doesn't disconnect through Yoke movement; but generally AP disconnects too quick from movement.
- Adjusted engine hot start and crank logic
- Fixed cut off numbers on VOR frequencies
- Fixed ALT HOLD not stopping climb from VS mode
- Fixed not able to use reverse thrust using key binds
- Fixed ADF needle jumping when signal limit reached
- General system stability improvements

We are version correcting this to 1.0.8 to establish a difference between the upcoming marketplace 1.07 version.

This update can be downloaded via the iniManager.

v1.0.8

Systems
- Fixed - VS mode reset to 0 at each waypoint in FP
- Fixed - When activating HDG mode while in PROFILE mode, PROFILE mode should stay engaged and not switch to LVLChg
- Fixed - Error in HP Valve Fire Loop Test Logic
- Fixed - Sometimes scrolling a value with the Honeycomb Bravo will also have the perceived effect of increasing sim rate
- Fixed - MDA input in FMC currently limited at 8000 (increased to 22000)
- Fixed - KDEN SIDs don't insert.
- Added – Exposed V1/VR/V2 LVARS. (INI_V1_FMGS, INI_VR_FMGS, INI_V2_FMGS)
- Added - Set chocks ON and park brake OFF when loading in cold & dark

Flight Model
- Improved ground handling flight model

Sounds
- Fixed – MCDU missing some sounds

EFB
- Added - Option in settings that allows refueling while engines running
 

This update can be downloaded via the iniManager.

v1.0.6
- Fixed further issues with AP not following LNAV.
- Fixed MCDU missing some sounds.
- Added custom reg and selcal options.
 

This update can be downloaded via the iniManager.

v1.0.5
- Fixed - When activating HDG mode while in PROFILE mode, PROFILE mode should stay engaged
- Fixed - ECAM says VLE at gear down is 250, should say 270 as on speed tape
- Adjusted the C&D panel state
- Fixed - [AFS] LNAV issues

This update can be downloaded via the iniManager.

v1.0.4

Art Fixes/Changes
- Fixed - EMER Exit Disarm light inop
- Fixed - N1 Max needle moving when it should be stationary
- Fixed - Missing flags on instruments when aircraft in C&D state
- Fixed - Pax: Crew Oxy gauges wrong, upper one should say HP
- Fixed - FO sun visor the wrong way round
- Fixed - Beacon lights flash marginally too quickly, should be once every second
- Fixed - Life vest decal not moving with chair
- Fixed - Phantom Orange Bug on EGT gauge
- Fixed - Integral light missing for ECAM display knobs

System Fixes/Changes
- Fixed - [VNAV] VNAV seems to be aiming for the FAF as the runway so the DECLL segment is too early
- Fixed - Opening CPT DH window closes the speed window, but the speed value can still be scrolled and changed
- Fixed - Block fuel totalizer only shows KG value 
- Fixed - Change POV L & POV R quickview
- Fixed - Possible to have less fuel in the aircraft when C&D
- Fixed - Unable to modify altitudes in GO AROUND PAGE
- Fixed - GPS altitude displays indicated altitude
- Fixed - Issues with entering airways
- Fixed - N2 Overspeed Pointer inop
- Fixed - Two adjustments for the C&D panel state
- Fixed - Waypoint entered in left MCDU on prog page will replicate on right MCDU
- Fixed - Some more routes where the TOC/BOD markers aren’t showing up
- Fixed - Manual selected VOR reverts to autotune - This might not be a bug
- Fixed - ECAM says VLE at gear down is 250, should say 270 as on speed tape
- Fixed - EGT starts at 84°C, should be OAT
- Fixed - Throttle goes into idle on bumpy runway

EFB Fixes/Changes
- Fixed - Auto tiller disconnect setting not saving
- Fixed - default THR setting not saving
- Fixed - Prepopulated weights always in KG
- Fixed - Door all close command missed R1
- Fixed – Oil replenishes itself between flights.

Sounds Fixes/Changes
- Fixed - ALT HLD sound switch plays when FMA mode changes 
- Fixed - GPWS callouts still a bit too quiet
- Fixed - some 1.0.3 sound feedback 
- Fixed - WX switch no sound from 2 to off
- Further sound mixing levels

Tool Tips Fixes/Changes

- Fixed - Dome Light missing TT

This update can be downloaded via the iniManager.

v1.0.3

Art Fixes/Changes
- Fixed - Shadow AO in Cabin
- Fixed - Flap animation too slow
- Fixed - F variant has slide arm stickers - also, action reversed
- Fixed - Disable HF displays / make rotary moveable
- Fixed - MCU Light Brightness Rotary doesn't dim lights
- Fixed – beacon light positions
- Fixed - Freighter: Cargo hall lights bleed through cockpit door
- Fixed - Extra dot on engine fuel display
- Fixed - Oil gauges: remove orange pointer, two words and two white dots missing
- Fixed - OVERHEAD / FUEL PUMPS PANEL
- Fixed - Galley AO texture

System Fixes/Changes
-  Fixed - When you turn off IRS 1 for you lose the ATT info on CPT PFD 
- Fixed - No fuel limitation on center tank
- Fixed - Smoke detector test
- Fixed - FMC not displaying waypoints on Airway page
- Fixed - Mach PreSelect not working
- Fixed - EFOB on CRZ and FUEL PRED page are different (possibly one is in KG, one in LBS)
- Fixed - LDA approaches missing RJTT
- Fixed - SPEED doesn't automatically change to MACH at 25400ft in LVL/CH mode
- Fixed - CPT FMS clearing properly on turnaround, but not FO
- Fixed - [FUEL] When fuel pumps selected off fuel tanks during gravity feeding still emptying
- Fixed - [FUEL] When FUEL ISOL valve is closed the fuel can still be drawn from the tank
- Fixed - ADF needles inop
- Fixed - Wrong TCAS test modelled
- Fixed - RMI Heading bug bug
- Fixed - Clock time counts faster when in external view
- Fixed - OPT and MAX FL should be based on weights entered in FMC, not the actual weights manipulated by EFB
- Fixed - TOD ETA in MCDU wrong
- Fixed - HYD fluids don't update on ECAM
- Fixed - Turning on engine anti ice should change n1 egt n2 etc 
- Added - Overtemp/speed pointers simulation on gauges and add max point reset on maintenance panel
- Fixed - Some A/THR, TO CONFIG and FPA issues
- Fixed - AP not upgrading from ALT* to ALT 
- Fixed - Because of above bug (ALT* to ALT) RNAV inop
- Fixed - ECAM shows wrong SPLRs are faulty when turning off blue hyd system
- Fixed - CG indication shows ZFWCG
- Fixed - Anti-Ice inop
- Fixed - MORE drag message not correct.
- Fixed - TCAS displaying all altitudes regardless of setting
- Fixed - Cant enter TROPO
- Fixed - "THR" not reverting to armed after target N1 on takeoff
- Fixed - [AFS] GW on ND not coming from weights typed into the FMS coming from sim weight 
- Fixed - [FMS] Change engine type to read A5 at the end not A1 
- Fixed - Aircraft not maintaining altitude in ALT
- Fixed - Logitech Radio Panels adjust active and not standby frequency
- Fixed - LDG INHIB and T.O. INHIB messages missing
- Fixed - TPR doesn’t follow Accel/THR red heights in FMS
- Fixed - TOC / BOD hockey sticks missing

EFB Fixes/Changes
- Fixed - Setting fuel in the EFB to 999999999999999999 and then click apply and instantly finishing the refuelling makes the plane bunnyhop.
- Fixed - Can't disarm door 4R
- Fixed – Maintenance has no effect on the aircraft
- Fixed - APU oil level drained to 0% after loading in 2/3 times few users also reported this on the discord. You can see the even counter is 21 but hours are 0 so should still have 39+ hours of fuel in 
-Fixed - Maintenance doesn't seem to work - nothing seems to be saved
- Added - Close the menu for panelstates once any panelstate button is pressed please
- Fixed - TORA no effect on V-Speeds
- Fixed - Takeoff Performance gives illogical numbers
- Fixed - Stutters caused by EFB
- Fixed - Generating new flightplan on SB doesn't refresh the Charts DEP/ARR even after pulling flightplan from SB again
- Fixed - Visuals for W/B when updating payload
- Fixed - Plane on Navigraph charts is offset
- Fixed - Perf page shows units as kgs if lbs are selected in settings
- Fixed - Weight on Perf page still shows lbs in column despite reflecting KG value
- Fixed - units on performance page not updating with selection in settings (values correct)
- Fixed - EFB performance not visually switching to imperial units
- Fixed - No LBS shown on payload or performance sections
- Fixed - Battery/Loading symbol flashing for me all the time
- Fixed - Altimeter settings don't stick
- Fixed - Unable to compute TO for values 170000 kg and above
- Fixed - TCA stuck in reverse
- Added - Deadzone to throttle calibration for reverse on axis throttles
- Fixed - When refuelling, fuel always starts at 0 and not the current fuel
- Fixed - No limit on payload fields
- Added – Ability to drag charts
- Added – many other suggestions for EFB charts
- Added – dark mode for charts
- Added – negative sign value for weather perf page 
- Added – Confirmation prompt to panel state buttons
- Added - OFP Viewer to EFB
- Added – A "disarm all doors" option to the EFB
- Fixed - EFB inserts wrong HDG into takeoff calc
- Fixed - Loading time remaining blocks FLEX value and chart controls
- Added - Deadzone to throttle calibration for reverse on axis throttles
- Added - Freighter: Way to unload the cargo. Once selected you can't unload it
- Fixed - When loading in with PAX and F and using a custom payload and pressing apply it seems to add full fuel for some reason when fuel was set to zero

Sounds Fixes/Changes
- Fixed - No change in ambient volume when FD door opened if main cabin door is open
- Fixed - Sound stage not changing when main cargo door is open
- Fixed - Spoiler sound stops after them being deployed
- Fixed - [GPWS] The time the GPWS callouts sound.
- Fixed - When BAT only sound even loops after I would guess 50 seconds 
- Fixed - FCU knob and button sounds not present anymore 
- Fixed - Wind noise seems rather inconsistent. 
- Fixed - Loop when at TOGA on the ground every 5-6 seconds 
- Fixed - Buzzsaw completely disappears as soon as behind the halfway point on the wing
- Fixed - GPWS sounds too quiet
- Fixed - When in the flight deck you can hear the flaps motor for about 1-2 seconds when they start moving, should not be able to hear them at all in flight deck
- Fixed - Can't hear the Altitude Alerter
- Fixed - Hissing point in the background noise during lower level climb out. It seems to fade in and out again 
- Fixed - When in flight with one engine shutdown and APU running you can hear that ELEC sound again even in flight 
- Fixed - Engine loop obvious at cruise
- Fixed - engine sound feedback
- Fixed - Missing sound event - CAPT/FO Oxy Test "hiss"
- Fixed - When turning on APU bleed with an entry door open (but cabin door closed) the external APU sounds seem to play in the flightdeck
- Fixed - Missing sound event - CAPT/FO Oxy Test "hiss"
- Fixed - When turning on APU bleed with an entry door open (but cabin door closed) the external APU sounds seem to play in the flightdeck

Whilst the team have been busy addressing the bugs, there are further changes coming next build to the EFB as well, so be on the look out for those!

This update can be downloaded via the iniManager.

v1.0.2

Art Fixes/Changes
Fixed - Holes in L1 door 
Fixed - HP VALVE should illuminate red during fire test
Removed - Ice detector probe
Added lights to ENT and CLR during IRS test
Fixed - make the window scratches less prominent
Added - Model circuit breakers that are relevant in checklists
Fixed - Tiller animation reversed when using Nose wheel steering axis
Fixed - Beacon bulb doesn’t flash with light 
Fixed - Cabin lights not showing in external view
Fixed - Cabin window tint
Fixed - FMS Glow reversed. Left FMC activates right glow source and vice versa
Fixed - Unable to dim MCDU lights
Fixed - Missing Backlight on Oxygen Panel Gauges
Fixed - MCP lights illuminate the center window column
Fixed - Rotate tires to different positions 
Fixed - internal door lock lever freighter
Fixed - APU Integrated LP fuel pump switch backwards
Fixed - Printer buttons lit when C&D
Added - Seat sliding back and forth
Fixed - Collision zones being too big
Fixed - EFB and Altitude select glass flicker in cockpit
Fixed - external light LOD issue
Fixed - Beacon lights not showing properly
Fixed - VOR/ADF gauges missing label
Fixed - Glass cover of the rear strobe light does not fit properly.

Systems Fixes/Changes
Fixed - Aircraft gives CG warning even though no CG has been entered
Fixed - Resetting it self back to zero when engines shutdown on older versions it didn't do this 
Fixed - WASM Crash - Loading waypoints too fast crashed aircraft on ground
Fixed - SEC WASM crash
Fixed - Next waypoint on ND distance doesn't change at the same time
Fixed - GPWS test/cancel PB not testing GPWS
Fixed - RMI Issue with 360
Fixed - Gear anims too slow 
Fixed - When directing, there is a small gap in drawn flight plan and distance is wrong
Fixed - auto disconnect tiller option not working
Fixed - When landing you get a triple click on touch down if landing with A/THR on you would not get this as the downgrade like modern Airbus 
Fixed - EGNX TNT 2N Departure
Fixed - AP not disconnecting on flight control input
Fixed – Green Dot calc in LBS and over 20,000ft seems to be wrong 
Fixed - Can't delete custom waypoint database
Fixed - EXT PWR AC Meter displays no frequency when EXT PWR is connected
Fixed - EMER Bus also showing voltage in C&D
Fixed - VS selects negative value single digit
Fixed – During climb or descent - Pressing ALT.HLD - Aircraft very slow to react (with High ROC, took 1800ft to react )
Fixed - DC EDD BUS during standby generator test
Fixed - NAV not following track 
Added - PLEASE WAIT prompt for VIA/GOTO on LAT REV as can take very long
Fixed - When VOR/NAV/ILS set to NAV, Glide indication appears in the vertical scale on PFD (should only appear in ILS Mode)
Fixed - Selected autobrake de-selects when gear is dropped
Fixed - Entering CG into PRG code crash
Fixed – Nose wheel steering tiller issues when using separate axis. Note the EFB ‘Rudder controls tiller’ option must be set to NO.
Fixed - Wildly varying fuel calcs on INIT B
Fixed - Esc sim / pause bug causing plane to break 
Fixed - PRE-SET speed works as it should, EXCEPT : On departure with Profile Armed, Should clear itself (replaced by ---) at acceleration altitude (currently stay PRESET until ALT* or LVL/CH pressed)
Fixed - Pressing the Status Page - When in normal, should revert automatically in MEMO Page (no need to press CLR pb)
Fixed - FMS not clearing properly on landing 
Fixed - APU FUEL LO PR ECAM still popping up with L INR TNK pumps off
Fixed - STEP ALTS page bringing up the wrong page
Fixed - PROF is re-engaging when reaching bugged altitude in LVL CHG
Fixed - Not able to insert KBDL into FROM/TO
Fixed - Freighter: cycling parking brake with engines off does not deplete the accumulator
Fixed - Sky high pressurisation bug
Fixed - Oxygen supply switch inop in pax version
Fixed - THS trims to aggressively
Fixed - Elevators don't drop down with no HYD
Fixed - Some users reporting that manually adding an alt constraint does not cause vnav path to recalculate
Fixed - OIL LO PRESS Never displayed (in low oil press condition)
Fixed - Added more details on the flow bar 
Fixed - When brake glow effect is active. So wheels above 550c the effect goes away when battery selected off.
Fixed - Changing restrictions has no effect
Fixed - Packs Off operations maybe wrong
Fixed - FMC freezes when inserting LFSB ILS15 approach
Fixed - VLS band doesn’t move when spoilers extend
Fixed - Engine Bleed Flow Bars 
Fixed - Seen two reports of people's pitots freezing despite having pitot heats on
Changed POV L & POV R quick view
Fixed – Incorrect turn at holding fix
Fixed - Revert active fix is white on ND change
Fixed - WASM crash with specific arrivals
Fixed FMA in Mach mode says SPEED, should say MACH
Fixed - PreSet light not extinguishing when switching to profile mode
Fixed - Selected Heading Index on RMI not working

Flight Model Fixes/Changes
Adjusted - interactive points to not crash when opened on the ground
Adjusted - Ground effect reduced to give a more natural entry feel 
Adjusted - CFD ground effect range reduced to give a better feeling near the end of the flare
Fixed - Reduced empty weight of pure F model to give larger payload range
Adjusted - Thrust output of engines adjusted at idle. Giving better idle rolling speed at all weight ranges.

Sounds Fixes/Changes
Fixed - The sounds internally are rather quiet compared to the external sounds, leading to a huge difference in volume when changing views between inside and outside
Fixed - Gear Thump Issue When the gear thumps occur, all other sounds are temporarily deadened.
Fixed - Engine 1 internal sounds don't seem to change with increased throttle
Fixed – Taxi gear cockpit ambient sound
Fixed - Whooler sound file seems quite low quality 
Fixed – engine sounds fade away
Fixed - Altitude Alert sound way too low
Fixed – Overall sound levels
Fixed - Windshear call out from ANN TEST light should play 3 times then stop not keep playing all the time
Fixed - All interior sounds are muted at some point during the gear sounds
Fixed - Right landing light no sound from Off to On
Fixed - GPU Loudness 
Fixed - Sounds seem to go mute at very fwd and very aft of cabin
Fixed - P/B sounds - All 6 buttons here do not make any sounds
Fixed - Avionics fans volume decreases when ENG 1 is running, even further when thrust applied
Fixed - Buzzsaw sound tied to explicit engine value of between 75-76%
Fixed - Engine sound levels during TOGA takeoff not quite right.
Fixed - MINIMUM callout not being called at DH
Fixed - Fuel pump sounds missing on the outside
Fixed - HYD sounds on external view are not audible unless right under LG bay
Fixed - Cabin/wing views have muted engine noise
Fixed - Fuel pumps seem to not be tied to fuel pump buttons high pitch sound can be heard all the time when AC power applied to aircraft even with pumps off and GPU on
Fixed - When aircraft sitting on stand the sound levels using drone camera don't make sense as it starts quiet gets louder and then stays that loud for a very far distance
Fixed – Flight deck is very loud but levels drop up and down
Fixed - Seats have no sound even when moved
Fixed - Eng1 v Eng2 exterior volume E2 is super soft in all phase vs it's twin. it's like 70-80% as loud in various povs around the aircraft.
 

This update can be downloaded via the iniManager.

v1.0.1

Fixed - Turnaround flight, block and ZFW fields not automatically cleared
Fixed  - DCT to bug causing crash bug fixed
Fixed - SFPI Speed brake light does not illuminate when speed brakes are extended 
Fixed -  TRP Should switch to GA at Slats extension
Fixed -  different F speed appears (depending on the 15/15 or 15/20 condition) 
Fixed - Wrong logic with the PRE-SET speed activation: Should only activate that speed when LVL/CH or ALT Selected or in ALT*
Fixed - ARC ILS rotation issue
Fixed - GSE items moving with rudder 
Fixed - Engine EGT reacts to fuel lever when engine is not started 
Fixed  -EHAM Runway degrees bug
Fixed - Pressurization gauges
Fixed -  Sim ATC reads COM3 by default
Fixed - Double P.DES FMA
Fixed  - Spawning on the RWY has no GW showing 
Fixed - GPU Indication issue 
Fixed - VNAV T/D improvements 
Fixed - Manual VOR/ADF tuning fixed 
Fixed - Above/Below waypoint constraints reversed on vert rev page
Fixed - Temperature limit in FMC fixed 
Fixed - APU low fuel pressure ECAM should go if any of the left hand pumps are on and isolation valves open
Fixed - Cabin Alt jumping up for seemingly no reason
Fixed - Active fix should be white on ND
Fixed -  Returning from pause can cause engines to cut out
Fixed - Green FMC glow present in C&D
Fixed - Cargo CONT knob issue fixed
Fixed - Spoilers in flight fixed
Fixed - Radio not working with Pro ATCX
Fixed - [v1.0.0] Yoke Movement
Fixed - FO sun blind isn't flipping down
Improved positions of light on tail  & fixed flipped turnoff lights 
Added commands for rudder via keyboard 
Removed CG autofill for erroneous GWCG calculation